www.zephyronline.com
Issue |
| Cause |
| What to do | Shooting |
|
|
| |||
|
|
|
|
|
|
After installation, the | 1. | The power source is not turned ON. | 1. | Make sure the circuit breaker and the |
|
unit doesn’t work? |
|
|
| unit’s power is ON. |
|
|
|
|
|
|
|
| 2. | The power line and the cable locking | 2. | Check the power connection with the |
|
|
| connector is not connecting properly. |
| unit is connected properly. |
|
|
|
|
|
| Trouble |
| 3. | The switch board and control board | 3. | Make sure the wirings between the | |
|
| ||||
|
| wirings are disconnected. |
| switch board and control board are |
|
|
|
|
| connected properly. |
|
|
|
|
|
|
|
| 4. | The switch board or control board is | 4. | Change the switch board or control |
|
|
| defective. |
| board. |
|
|
|
|
|
|
|
Light works, but motor is | 1. | The motor is defective, possible | 1. | Change the motor. |
|
not turning. |
| seized. |
|
|
|
|
|
|
|
|
|
| 2. | The thermally protected system | 2. | The motor will function properly after the |
|
|
| detects if the motor is too hot to |
| thermally protected system cool down. |
|
|
| operate and shuts the motor down. |
|
|
|
|
|
|
|
|
|
| 3. | Damaged condenser. | 3. | Change the condenser. |
|
|
|
|
|
| |
The unit is vibrating. | 1. | The motor is not secure in place. | 1. Tighten the motor in place. |
| |
|
|
|
|
| |
| 2. | Damaged blower wheel. | 2. Change the blower wheel. |
| |
|
|
|
|
| |
| 3. | The hood is not secured in place. | 3. Check the installation of the hood. |
| |
|
|
|
|
|
|
The motor is working, | 1. | Defective halogen bulb. | 1. | Change the halogen bulb. |
|
but the lights are not. |
|
|
|
|
|
| 2. | The light bulb is loose. | 2. | Tighten the light bulb. |
|
|
|
|
|
|
|
The hood is not venting | 1. | The hood might be hanging to high | 1. | Adjust the distance between the cook |
|
out properly. |
| from the cook top. |
| top and the bottom of the hood within |
|
|
|
|
| 24” and 32” range. |
|
| 2. | The wind from the opened windows or | 2. | Close all the windows and doors to |
|
|
| opened doors in the surrounding area |
| eliminate the outside wind flow. |
|
|
| are affecting the ventilation of the |
|
|
|
|
| hood. |
|
|
|
| 3. | Blocking in the duct opening or | 3. | Remove all the blocking from the duct |
|
|
| ductwork. |
| work or duct opening. |
|
| 4. | The direction of duct opening is | 4. | Adjust the duct opening direction. |
|
|
| against the wind. |
|
|
|
| 5. | Using the wrong size of ducting. | 5. | Change the ducting to at least 8” or |
|
|
|
|
| higher. |
|
|
|
|
|
|
|
Metal filter is vibrating. | 1. | Metal filter is loose. | 1. | Change the metal filter. |
|
|
|
|
|
|
|
19