Vermont Casting DVR33 manual Fan Kits, Hard Wire Direct Hook-Up

Page 37

Vermont Castings, Majestic Products: DVR33

Optional Accessories

Fan Kits

FK-12 Fan Assembly

1.Open lower louvre.

2.Install FK12 fan in back of unit between hearth supports (Fig. 49).

3.Secure fan on Velcro strips.

4.Power to the fan can be supplied by plugging the supply lead into a conveniently located wall socket or by using a hard-wired EB-1 connector box.

5.Be sure fan motor does not touch nearby metal.

Side View

Cold Air

Box

Front of

Unit

Hearth Pan

Base Pan

FK12 Fan

 

FP1004

Fig. 49 FK-12 Fan placement.

FK-24 Fan Assembly

Fan specifications: 120 volt, 60 Hz, 0.75 Amp.

This fan does not need regular maintenance, however periodic cleaning is required. Check the area under the control door and in front of the fan and wipe or vacuum at least once a month during the operating season.

Should this fan require servicing, the power supply must be disconnected.

The FK-24 comes with the electrical cord attached.

1.Slide fan assembly from the left side into the fireplace opening, line up mounting holes with screw studs on back of fireplace and fasten with #10-24 hex nuts.

2.Install thermal sensor on bottom of firebox using #10-24 hex nuts.

3.Option A– Place electronic fan speed control box on bottom of fireplace base, lining up mounting holes with screw studs. Fasten fan speed control box with #10-24 hex nuts.

Option B– The speed control can be installed in an electrical box at normal wall switch height for convenient access.

4.Connect the power supply in one of two ways:

Method A

Route the 6’ (1.8 m) lead fitted to the unit to a conveniently located wall socket.

Method B

If EB-1 receptacle box (Pt. #ZA1200) was correctly connected when the unit was installed, the fan lead can be directly plugged into the EB-1 plug socket.

5.Whether wiring directly to the fan junction box (Option A), or into EB-1 electrical receptacle box (Option B), first ensure cable is secured using box connector.

The fireplace, when installed must be electrically connected and grounded in accordance with local codes, or in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or for USA installations, follow local codes and the National Electrical Code, ANSI/NFPA No. 70.

Hard Wire (Direct) Hook-Up

First connect ground wire to ground stud located on the base of either box. Black wire from supply should connect to the variable speed switch. Alternate speed switch wire connects to temperature sensor. Alternate lead from sensor connects to fan. Alternate fan lead connects back to the white supply wire (Fig. 51).

Electrical Box

Heat

Fan

 

 

 

Sensor

 

 

 

 

F

P

 

 

 

 

TO

 

 

 

Fan Speed

Gas Line

Valve

 

Switch

 

 

 

 

 

FP1026

 

 

 

 

 

Fig. 50

FK-24 fan placement.

 

 

 

 

 

 

 

 

 

Fan

Temperature Sensor

Speed Control

Black

White

Ground

FP1025

Fig. 51 FK-24 fan wiring.

Any electrical rewiring of this fan must be completed by a qualified electrician.

Turn off all power before hookup.

10004920

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Rear Vented Direct Vent Gas Fireplace Model DVR33 Table of Contents Locating Your Fireplace Installation and Operating InstructionsAppliance Dimensions Fireplace DimensionsFraming Dimensions Mantels Clearance to CombustiblesHearth Framing and Finishing Gas SpecificationsFinal Finishing Gas Inlet and Manifold PressuresRemote ON/OFF Switch Installation Gas Line InstallationAlternate Switch Location EB-1 Electrical Box Electronic Gas Control Valve General Venting InformationGeneral Venting Information-Termination Location Canadian Installations1 US Installations2Canadian Installations General Information for Connecting Vent PipesUSA Installations Crimped End PipesTwist Lock Pipes Rear Wall Vent InstallationRear Wall Vent Application Vent Opening Noncombustible Wall Vent Opening Combustible WallVertical Sidewall Application How To Use the Vent GraphExample a Example BMax 914 mm Vent Opening Noncombustible Wall Vertical Sidewall Installation7DVSKS Below Grade InstallationVertical Through-the-Roof Applications Snorkel installation, recessed foundationMin ’ 610 mm Vertical Through-the-Roof InstallationDVR33 Bracket Restricter Installation Twist Lock Venting Components Crimped End Venting Components Glass Cleaning Window Frame Assembly RemovalOperating Instructions Glass InformationInstallation of Logs Lava Rock Material Flame and Temperature AdjustmentInspecting the Venting System Flame CharacteristicsTo Turn Off Gas To Heater Lighting and Operating InstructionsLighting Instructions Lighting and Operating InstructionsTurning Off the Gas to the Appliance Window Frame Assembly Should be Removed Before Service Work Troubleshooting Honeywell Millivolt ValveTroubleshooting the Gas Control System SIT 822 Valve with a Honeywell Electronic Igniter Fuel Conversion Instructions Cleaning Standing Pilot Control System General MaintenanceFK24/FK12 Fan Assembly Burner and Burner CompartmentDVR33 DVR33 Vermont Castings, Majestic Products DVR33 Vermont Castings, Majestic Products DVR33 Fan Kits Hard Wire Direct Hook-UpCeramic Refractory Panels Remote ControlsDecorative Bay Windows Bay window Decorative Frame TrimsLimited Lifetime Warranty

DVR33 specifications

The Vermont Casting DVR33 is a prominent name in the hearth solutions market, known for blending exceptional design with advanced heating technology. This distinctive gas fireplace is engineered to offer both efficiency and aesthetic appeal, making it a valuable addition to any home.

One of the primary features of the DVR33 is its realistic flame presentation. Utilizing advanced gas burner technology, it creates a mesmerizing fire that mimics the beauty of traditional wood-burning fireplaces. The flames dance and flicker, providing warmth and comfort while generating an inviting ambiance that enhances any living space.

The DVR33 is designed with energy efficiency in mind. With an efficiency rating of up to 80 percent, this model ensures that minimal heat is lost, making it a cost-effective heating solution. It is also equipped with a sealed combustion system that draws air from outside for combustion, ensuring improved indoor air quality and reducing energy costs.

Safety is another critical aspect of the DVR33. It comes with an electronic ignition system that ensures reliable performance without the need for continuous pilot lights, thus conserving energy. The adjustable flame height and heat output provide users with control over their heating needs, allowing for personalized comfort levels depending on the season or occasion.

Aesthetically, the DVR33 offers a customizable design. Homeowners can select from various fronts, finishes, and decorative options, allowing them to seamlessly integrate the fireplace into their existing decor. The unit also includes a realistic ceramic log set that enhances the lifelike appearance of the flames.

In terms of maintenance, the DVR33 is designed for convenience. It requires minimal upkeep, and the accessible controls simplify operation. Additionally, Vermont Castings offers an impressive warranty, underscoring their commitment to quality and customer satisfaction.

Overall, the Vermont Casting DVR33 stands out as a high-quality gas fireplace that combines technology, efficiency, and design. With its beautiful flame presentation, customizable options, and focus on safety, it’s an ideal choice for anyone looking to enhance their home with the warmth and elegance of a gas fireplace.
Top Page Image Contents