Vermont Casting DVR33 manual Remote Controls, Ceramic Refractory Panels, Decorative Bay Windows

Page 38

Vermont Castings, Majestic Products: DVR33

Remote Controls

Optional remote control units are available to control different functions of the appliance (only for RN/RP models).

Model

Function(s) Controlled

MRC1

ON/OFF

MRC2

ON/OFF and Temperature

MRC3

ON/OFF and Temperature control

 

with a digital display and a

 

programmable 24-hour clock

IMT

Wall-mounted thermostat control

Ceramic Refractory Panels

Adjustable

 

 

tab

 

Adjustable

 

 

 

 

tab

Side

Back Panel

Log

panel

Support

 

 

 

Side

 

BURNER HOUSING

panel

 

ASSEMBLY

 

Lower

 

Lower

side

 

side

support

 

support

Floor refractory panel

FP1193

Fig. 52 Install ceramic refractory panels.

Ceramic refractory panels are available to line the firebox area.

Unit

Kit Model

DVR33DVR33CR

Take care when handling the refractory panels as they are fragile until held in place and supported.

Installation (refer to Fig. 52 and Fig. 54)

Rear Refractory Panel

Rear Panel

Support Brackets

Rear Log Support

Firebox Back

FP1194

1.Remove the window frame assembly

2.Remove the logs.

3.Place the lower supports for the side refractory panels on the base of the firebox. Place each support so that the slotted hole fits over the forward screw head along the edge of the base.

4.Lay the angular base panels in place on the floor of the firebox on either side of the burner housing assembly.

5.Loosely attach the top adjustable tabs to the studs located in the top of the firebox toward the front corners.

6.Place the rear refractory panel in place. Locate the ‘small brick’ edge of the panel into the two small supports on the back panel just above the rear log support.

7.Slide the side refractory panels into place to hold the rear panel secure. Adjust the top adjustable tabs to hold the side panel against the firebox wall and secure the tab. Repeat the procedure on the other side.

8.Replace the logs and window frame assembly.

NOTE: For aesthetic purposes, we recommend aligning the horizontal mortar lines.

Fig. 53 Place the rear panel on rear support brackets.

Decorative Bay Windows

The original front frame/glass assembly MUST remain in place when fitting the bay window kits. The bay window kit fits over existing front glass.

Bay window kits are available for model DVR33 fireplace.

Installation

1.Remove the existing louvre assembly bottom complete with the hinges.

2.Remove the louvre assembly top.

3.Assemble the Bay Window Kit according to the instructions supplied with the kit.

4.Place the 2 pieces of ceramic refractory along the base of the bay window (Fig. 54).

5.Hang the Bay Window Assembly over the existing window frame assembly.

6.Reinstall the upper louvre assembly.

Do not remove the existing window frame assembly.

38

10004920

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Rear Vented Direct Vent Gas Fireplace Model DVR33 Table of Contents Installation and Operating Instructions Locating Your FireplaceFraming Dimensions Fireplace DimensionsAppliance Dimensions Hearth Clearance to CombustiblesMantels Final Finishing Gas SpecificationsFraming and Finishing Gas Inlet and Manifold PressuresAlternate Switch Location Gas Line InstallationRemote ON/OFF Switch Installation EB-1 Electrical Box General Venting Information Electronic Gas Control ValveCanadian Installations1 US Installations2 General Venting Information-Termination LocationUSA Installations General Information for Connecting Vent PipesCanadian Installations Crimped End PipesRear Wall Vent Application Rear Wall Vent InstallationTwist Lock Pipes Vent Opening Combustible Wall Vent Opening Noncombustible WallExample a How To Use the Vent GraphVertical Sidewall Application Example BMax 914 mm Vertical Sidewall Installation Vent Opening Noncombustible WallBelow Grade Installation 7DVSKSSnorkel installation, recessed foundation Vertical Through-the-Roof ApplicationsVertical Through-the-Roof Installation Min ’ 610 mmDVR33 Bracket Restricter Installation Twist Lock Venting Components Crimped End Venting Components Operating Instructions Window Frame Assembly RemovalGlass Cleaning Glass InformationFlame and Temperature Adjustment Installation of Logs Lava Rock MaterialFlame Characteristics Inspecting the Venting SystemLighting and Operating Instructions To Turn Off Gas To HeaterTurning Off the Gas to the Appliance Lighting and Operating InstructionsLighting Instructions Troubleshooting Honeywell Millivolt Valve Window Frame Assembly Should be Removed Before Service WorkTroubleshooting the Gas Control System SIT 822 Valve with a Honeywell Electronic Igniter Fuel Conversion Instructions FK24/FK12 Fan Assembly General MaintenanceCleaning Standing Pilot Control System Burner and Burner CompartmentDVR33 DVR33 Vermont Castings, Majestic Products DVR33 Vermont Castings, Majestic Products DVR33 Hard Wire Direct Hook-Up Fan KitsDecorative Bay Windows Remote ControlsCeramic Refractory Panels Decorative Frame Trims Bay windowLimited Lifetime Warranty

DVR33 specifications

The Vermont Casting DVR33 is a prominent name in the hearth solutions market, known for blending exceptional design with advanced heating technology. This distinctive gas fireplace is engineered to offer both efficiency and aesthetic appeal, making it a valuable addition to any home.

One of the primary features of the DVR33 is its realistic flame presentation. Utilizing advanced gas burner technology, it creates a mesmerizing fire that mimics the beauty of traditional wood-burning fireplaces. The flames dance and flicker, providing warmth and comfort while generating an inviting ambiance that enhances any living space.

The DVR33 is designed with energy efficiency in mind. With an efficiency rating of up to 80 percent, this model ensures that minimal heat is lost, making it a cost-effective heating solution. It is also equipped with a sealed combustion system that draws air from outside for combustion, ensuring improved indoor air quality and reducing energy costs.

Safety is another critical aspect of the DVR33. It comes with an electronic ignition system that ensures reliable performance without the need for continuous pilot lights, thus conserving energy. The adjustable flame height and heat output provide users with control over their heating needs, allowing for personalized comfort levels depending on the season or occasion.

Aesthetically, the DVR33 offers a customizable design. Homeowners can select from various fronts, finishes, and decorative options, allowing them to seamlessly integrate the fireplace into their existing decor. The unit also includes a realistic ceramic log set that enhances the lifelike appearance of the flames.

In terms of maintenance, the DVR33 is designed for convenience. It requires minimal upkeep, and the accessible controls simplify operation. Additionally, Vermont Castings offers an impressive warranty, underscoring their commitment to quality and customer satisfaction.

Overall, the Vermont Casting DVR33 stands out as a high-quality gas fireplace that combines technology, efficiency, and design. With its beautiful flame presentation, customizable options, and focus on safety, it’s an ideal choice for anyone looking to enhance their home with the warmth and elegance of a gas fireplace.
Top Page Image Contents