Zanussi ZCG 7900X manual Connecting to GAS, Connection to the Electricity Supply

Page 46

4. CONNECTING TO GAS

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE:

ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Check for gas soundness after connecting to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig.3. Take into account that it must be possible to pull the appliance forward sufficiently. The hose must not get caught on the stability bracket.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS. 669 CURRENT EDITION.

50 100

850

Fig.3

700

L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50 mbar AND TO CARRY A RED STRIPE, BAND OR LABEL.

250

450

All dimensions in mm

5. CONNECTION TO THE ELECTRICITY SUPPLY

WARNING: THIS APPLIANCE MUST BE EARTHED. DO NOT EARTH THIS APPLIANCE TO THE GAS SUPPLY PIPING.

This appliance must be connected to 220V-240V A.C. 50Hz supply. It is supplied with 2 metres of 5 amp 3 core

cable incorporating a moulded 13 amp plug , fitted with aFig.4 3 amp fuse, which can be plugged directly into the

nearest suitable socket. If this is not long enough, the supply cable can be replaced totally by a longer cable at least 0.75mm² nominal cross sectional area (24/0.2mm).

IF THE MOULDED PLUG IS CUT FROM THE CABLE

FOR ANY REASON, IT MUST BE DESTROYED OR

DISPOSED OF SAFELY, AS THE PROTRUDING

WIRES WILL BE AN ELECTRIC SHOCK HAZARD.

If any other type of plug is used it should incorporate a 5 amp fuse in either the plug or adapter or at the distribution board.

If the cable has to be threaded through small apertures in cabinets etc., it may be disconnected from the appliance, then re-connected to as shown in Fig.4.

DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND/OR INSULATION TAPE.

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH I.E.E. WIRING REGULATIONS.

46

Image 46

Contents ZCG For your safety IntroductionContents Lighting the cooker HotplateGrill Grill/second ovenSecond oven Oven light Main ovenTo turn off any burner Oven will lightCooking positions GrillHeat control PreheatingGrill pan and handle Positioning food on the gridGrill pan should be fitted with the handle for grilling Hotplate Burner sizesUse pans with flat bases. They are more stable Take care to avoid burns and scalds when youAre reaching across the hotplate Than pans which are warpedHelpful hints Heat zones OvensOven shelves Baking trays and dishes Roasting CondensationOven cooking chart Main oven Mins. per ½kg 1lb and 25 mins 30 40 mins Lamb Shelf on Medium Oven cooking chart Second ovenBase Medium Base Well DoneFruit pie shortcrust 25 35 mins 45 60 mins Baked custard 50 60 minsTo set the time of day Electronic timerTurn the selector knob to Manual then turn to Time Setting To use the countdownSetting knob Either direction Setting the controls for automatic useAutomatic control Display What time do Turn the selector knob to You want G 7 9 0 0 How long will Turn the selector knob to Food takeTo cook? Food to beHints and tips for automatic cooking Food preparation slow cooking Slow cookingPlease note There is no slow cook on the second oven Thaw thoroughly before cooking Do not cook casseroles over 3kg 6lbLeft over food should be cooled quickly and refrigerated Care and cleaning For your safety Clean the grill frequently using hot soapy water Crown to body Do not try to force the crown on to the bodyOvens To carry out a cleaning cycle Remove the oven shelves Main oven cleaning cycleGeneral Remove the oven shelf Top oven cleaning cycleSet the oven to mark 5 for at least 30 minutes Cleaning between the outer and inner door glass To remove the outer glassLocation Cleaning The Door GlassInstalling the cooker Make sure that a stability bracket is fittedHeight to hotplate 900mm 920mm Cooker dimensionsPositioning Width 594mm DepthConnecting to the electricity supply General information For your safetyMoving your cooker Replacing the oven light bulb What is wrong and why? CheckProbably a fault Service and spare parts 7 0 5 9 2 9 9 2Customer Care Department Installation Instructions Ignition DimensionsConnections GrillSecond Oven Important Safety RequirementsMain Oven GeneralLocation of Appliance Levelling the Appliance Parts RequiredFitting the Stability Bracket Connecting to GAS Connection to the Electricity SupplyChecking the Hotplate Pressure TestingChecking the Grill Checking LID SHUT-OFF DeviceChecking the Main Oven Checking the Main Oven ControlsAutomatic Operation Checking the Main Oven Light Checking the Second OvenGeneral Note Guarantee Conditions ZCG7900XPage Electrolux Household Appliances Limited From the Electrolux Group. The worlds No choice