Sherwood P-965 manual Connecting PC for Upgrades

Page 13

11. CONNECTING PC FOR UPGRADES

•This unit incorporates USB as well as RS-232C terminal that may be used in the future to update the operating software so that it will be able to support new digital audio formats, external control by using an external device and the like.

•Connect either USB or RS-232C terminal to your PC(You don’t need to do both).

PC with USB

or RS-232C port

UPGRADE switch

ENGLISH

Notes :

•Be sure to set the UPGRADE switch to “SVC”(service) before updating.

•This switch should be set to “OPR”(operation) during normal operation except for upgrades.

If not, this unit will not operate normally.

•Programming for upgrades and external control requires specialized programming knowledge and for that reason we recommend that it only be done by qualified installers. For more information on future upgrades and external control, visit the Sherwood web site at www.sherwoodamerica.com or contact your dealer.

•Do not disconnect the connection cable while updating the operating software, etc. Should this happen, it may be result in malfunction or cause damage to the unit.

12. SWITCHED AC OUTLETs

•These outlets are switched on(power-on mode) and

off(standby mode) according to power control as follows(Maximum total capacity is 100 W, 1A).

Standby mode - Switched AC outlet off

Power-on mode - Switched AC outlet on

13. AC INLET

•Plug the supplied AC input cord into this AC INLET and then into the wall AC outlet.

Note:

•Do not use an AC input cord other than the one supplied with this unit. The AC input cord supplied is designed for use with this unit and should not be used with any other device.

To a wall AC outlet.

13

Image 13

Contents

965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Video 1 Video deck, DVD recorder, etc Component video input default settingsUSB audio connection Digital input default settings Connecting 8CH Direct INs Front left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE Loading Batteries Remote Control Operation RangeEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsBefore operation OperationsAdjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundDolby Pro Logic IIx surround Front L/R Center DSP DSP Enjoying Surround SoundTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Speaker Setup When selecting the Speaker Configuration Setting the Speaker SetupWhen selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupVOL Main FAV When selecting the Digital Input Setup Setting the System SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuidePRE Amplifier Section Specifications965