Sherwood P-965 manual Adjust the level of the selected channel as Desired

Page 33

Adjust the level of the selected channel as

2 desired.

PAGE

MAIN

FAV

VOL

CH/

or	ADJUST

		1	2	3
DOWN	UP	4	5	6
DOWN	UP	7	8	9
			0
		MI	M2	M3

3	Repeat the above steps	and	to adjust
3	each channel level.

ENGLISH

Adjusting the Dolby Pro Logic IIx / Dolby Pro Logic II Music parameters

•When selecting either the Dolby Pro Logic IIx Music mode or the Dolby Pro Logic II Music mode depending on whether “S/B CH” is set to “None” or not, you can adjust the various surround parameters for optimum surround effect.(Refer to “When selecting the SPEAKER CONFIGURATION” on page 44.)

•In case of PL IIx MUSIC mode, only when original surround mode is “BYPASS” mode or 2 channel digital signals from Dolby Digital sources, etc. are input, these parameter settings affect the surround effects.

Press the DOLBY PL II MUSIC PARAMETER button to select the desired parameter.

1	• Each time this button is pressed, the parameter changes and is
	displayed for several seconds as follows;

or

STANDBY

POWER ON

AUD2

SLEEP D/A

DIMM S.A/B

ROOM2 SUR.B

T.TON PURE

OSD PARA.

PAGE1

Panorama mode(“PANORAMA”, default value : OFF) This mode extends the front stereo image to include the surround speakers for an exciting “wraparound” effect with side wall imaging. Select “OFF” or “ON”.

Center width control(“C-WIDTH”, default value : 0)

This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees.

The control can be set in 8 steps from 0 to 7.

Dimension control(“DIMENSION”, default value : 0)

This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -3 to +3.

At the desired parameter, adjust it as desired.

2

PAGE

MAIN

FAV

VOL

CH/

or

ADJUST

1 2 3

4 5 6

7 8 9

0

MI M2 M3

• If the parameter display disappears, start from the step again.

3	Repeat the above steps	and	to
3	adjust other parameters.

33

Image 33

Contents

965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Video 1 Video deck, DVD recorder, etc Component video input default settingsUSB audio connection Digital input default settingsConnecting 8CH Direct INs Front left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE Loading Batteries Remote Control Operation RangeEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsBefore operation OperationsAdjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundDolby Pro Logic IIx surround Front L/R Center DSP DSP Enjoying Surround Sound2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Speaker Setup When selecting the Speaker Configuration Setting the Speaker SetupWhen selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupVOL Main FAV When selecting the Digital Input Setup Setting the System SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Surround Mode is selected When the Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuidePRE Amplifier Section Specifications965