Frigidaire FGUN2642LP, FGUS2647LF manual To Connect Water Supply Line To Ice Maker Inlet Valve

Page 14

CONNECTING THE WATER SUPPLY

To Connect Water Supply Line To Ice Maker Inlet Valve

1.Disconnect refrigerator from electric power source.

2.Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.

3.Remove plastic cap from water valve inlet and discard cap.

4.If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch/6 mm). Slide ferrule

(sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 1.

If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 2.

5.With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.

6.Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

7.Turn ON water supply at shutoff valve and tighten any connections that leak.

8.Reconnect refrigerator to electrical power source.

Plastic Water

Steel

Tubing to Ice

Clamp

Maker Fill

Brass

Tube

Compression

 

Nut

 

Ferrule

 

(Sleeve)

 

Copper

 

water line

 

Water Valve

 

Bracket

 

Valve Inlet

 

Water Valve

 

Copper water line

 

from household

 

water supply

(Include enough tubing in loop to allow moving refrigerator out for cleaning.)

Figure 1

Plastic Water Tubing

Steel

to Ice Maker

Fill Tube

Clamp

Stainless

Steel

water line

Water Valve

Bracket

Valve Inlet

Water Valve

6 ft. Stainless Steel water line from household water supply

Figure 2

14

Image 14
Contents Use &Care Important Safety Instructions Electrical information Features AT a Glance Features may vary according to modelRequired Tools InstallationInstallation LocationLeveling Freezer Drawer if necessary Level Refrigerator & AdjustTo level the cabinet using the front rollers select models Doors if necessaryRetighten screw To adjust the door stopDoor stop is adjustable between 85 to 145 degrees Ensure door stops in desired locationTo adjust the flipper mullion Loosen the screw located on the flipper mullion hingeTo prepare for removing the doors Door Removal InstructionsGetting through narrow spaces To remove the top hinge coversOpen freezer drawer Installing Freezer DrawerRemoving Freezer Drawer Installing Door Handles Door Handle Mounting Instructions for Frigidaire GalleryMounting Refrigerator Handles Connecting the Water Supply Before Installing The Water Supply Line, You Will NeedTo Connect Water Supply Line To Ice Maker Inlet Valve IQ-TouchTM AlarmsControls IQ-TouchTMSabbath Mode Automatic ICE Maker select models Drawers Storage FeaturesShelf features CrispersTo change the position of an adjustable door bin Accessories varies by model Dairy compartmentFreezer Features varies by model Deli drawerDividers Removal To Remove Upper BasketTo Remove Lower Basket Storing Food and Saving Energy Normal Operating Sounds and Sights Understanding the sounds you may hearChanging the Filter Air filter select models Air Filter Reset will turn itself off after a few secondsAir Filter Replacement cartridge, Paultra Replacing your PureAdvantageTM air filterCare & Cleaning Protecting your investmentGone a few days Care and cleaning tipsVacation and moving tips To replace LED Lights Ordering Replacement LED LightsReplacing LED Lights select models Replacing Light Bulbs select modelsBefore YOU Call United States CanadaRefrigerator CompressorDoes not run Runs too muchMajor Appliance Warranty Exclusions This warranty does not cover the following