Sherwood R-865 manual Room 2 connections, Main room Another roomRoom

Page 12

ENGLISH

ROOM 2 connections

•ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main room at the same time.

•For ROOM 2 playback, connect the VIDEO 2 / ROOM 2 OUT jacks to the amplifier, TV, etc. installed in another room, or connect the SURROUND BACK speaker terminals to the speakers.

•In case of using a pair of speakers only, you should assign the power amplifier for surround back channels to the ROOM 2.(For details, refer to “SELECTING THE POWER AMP ASSIGN” on page 49.)

Notes :

•To minimize hum or noise, use high quality connected cords.

•You cannot use the digital audio signal for ROOM 2 playback.

Main room

Another room(Room 2)

•When connecting VIDEO 2/ROOM 2 OUTs to the components.

This receiver

ININ

S-VIDEO VIDEO (COMPOSITE)

TV or projector

L AUDIO

R IN

AmplifierSpeakers

•When connecting SURROUND BACK speaker terminals to the speakers.

This receiver

Speakers

left right

10. CONNECTING MULTI-ROOM SYSTEM KIT

•The multi-room system kit (sold separately ) is essential for operation from a remote location.

For information on the multi-room kit, contact the Xantech corporation at 1-800-843-5465 or www.xantech.com.

•IR IN jack allows you to control this receiver from another room with the remote control unit.

•To control this receiver from another room with the remote control unit, connect the IR IN jack to the output of the connecting block.

•If this receiver is located inside a cabinet or other enclosure where the infrared beams from the remote control unit cannot enter, then operation with the remote control unit will not be possible.

In such a case, connect the IR IN jack to the output of the connecting block.

Note:

•Remote operation may become unreliable if the IR receiver is exposed to strong light such as direct sunlight or inverted fluorescent.

Main room

This receiver

Connecting block (Multi-room system kit)

output

Another room(Room 2)

IR receiver (Multi-room system kit)

•When this receiver is located inside a cabinet.

In the cabinet

This receiver

output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting block

IR receiver

(Multi-room system kit)

(Multi-room system kit)

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 865 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Component in 1 Video 1, Component in 2 VideoDigital input default settings VideoConnecting System Control Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerRoom 2 connections Main room Another roomRoomConnecting Microphone Front Panel Controls Dolby PL II Music ParameterRemote Sensor Fluorescent DisplayFluorescent Display Universal Remote Controls LCD ScreenFunction Table of the Numbered Buttons Device to be ControlledRemote Control Operation Range Loading BatteriesUsing Functions of Remote Control Entering a setup codeLearn Delete Macro Code Punch Searching a setup code Programing the commands from other Remote controls Learning modeErasing the programmed command Erasing all the commandsProgrammed under a device mode From one buttonProgramming a macro function Operating a macro functionTo erase a macro program To change a macro programPrograming a punch-through function Audio Delete TVCD Delete DVD VCR AUX TV Delete SAT Cable VCROperating a punch-through function Erasing the programmed puch-through functionVOL Delete Play CH English Room 2 Remote Controls Volume UP/DOWN ButtonsOperations Listening to a Program SourceBefore operation Tuner CD AUXWhen CD, AUX or Video 1~ Video 4 is selected Adjusting the tone bass and trebleDigital Analog Muting the sound Listening with the headphones Surround Sound Surround modesTheater Front L/R Center Enjoying Surround Sound PL II Music2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Compressing the dynamic rangeDolby Digital sources only Entering a label Correcting or clearing a labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration English When selecting the Speaker Distance DownWhen selecting the Virtual Speaker Setup When selecting the Subwoofer When selecting the Subwoofer Mode When selecting the CrossoverWhen selecting the Auto Speaker Setup PreparationsTo confirm the results, press the Cursor Left /RIGHT Setting the System Setup When selecting the Digital Input SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup When selecting the Video 2 OUT When selecting the DC Trigger Setup When the DC Trigger mode is set to OnWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Surround Mode is selected When the Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionDigital Audio Section Setup Code Table RCA SSSTMK CCESTS KLHMEI ABC NSCSAT HTSDKK MCSNSM QED865

R-865 specifications

The Sherwood R-865 is a remarkable audio receiver that encapsulates the essence of home audio entertainment. Belonging to the renowned Sherwood brand, this model is a perfect blend of vintage aesthetics and modern engineering, making it a prized addition for audiophiles and casual listeners alike.

At the heart of the Sherwood R-865 lies its powerful amplification section, designed to deliver exceptional sound quality and maintaining audio fidelity across various frequencies. The receiver supports 5.1 channel surround sound, making it an ideal choice for those who enjoy immersive audio experiences in their home theater setups. With a power output of up to 100 watts per channel, the R-865 can easily drive a variety of speaker systems, resulting in detailed sound reproduction that brings movies, music, and games to life.

One of the standout features of the R-865 is its advanced digital signal processing capabilities. This technology not only enhances audio clarity but also ensures that users can enjoy an optimized sound experience tailored to their room's acoustics. The inclusion of multiple sound modes further allows listeners to choose settings that suit different genres of music or types of content, whether it be movies, music, or sports.

Connectivity is another strong point for the Sherwood R-865. It offers a variety of inputs, including HDMI, optical, and coaxial ports, ensuring compatibility with a wide range of sources such as Blu-ray players, gaming consoles, and streaming devices. Additionally, it features built-in Bluetooth technology, allowing users to stream their favorite songs directly from smartphones or tablets without the hassle of wires.

The receiver's user interface is designed with convenience in mind. The LCD display makes it easy to navigate through settings and inputs, while the remote control provides users with extensive control options from the comfort of their couch. For those who appreciate the aesthetics of home audio equipment, the Sherwood R-865 also sports a timeless design with clean lines and a classic finish that complements any home décor.

Moreover, the R-865 offers a robust equalizer feature, enabling users to fine-tune audio outputs to match their unique listening preferences. The receiver also includes various safety features such as short-circuit protection and thermal overload safeguards, ensuring reliable operation over long periods.

In summary, the Sherwood R-865 audio receiver packs a punch with its state-of-the-art audio technologies, versatile connectivity options, and user-friendly design. Whether you’re throwing a movie night or hosting a listening party, this receiver stands ready to deliver an unparalleled audio experience that everyone can enjoy.
Top Page Image Contents