Sherwood R-865 manual Programing the commands from other, Remote controls Learning mode

Page 21

Programing the commands from other

Press and hold down the ENTER button

and the desired one of the DEVICE buttons

remote controls( LEARNING mode )

2 for more than 2 seconds.

 

• If the setup codes are not available for your component or you want to program a missing or special function into one button of a device, the learning function enables this remote control to learn the commands from other remote controls.

Place this remote control and other remote

1 control facing each other at a distance of 5 to 15 cm (2 to 6 inches ) apart.

 

 

• Then “LEARN” is displayed on the LCD screen for

 

 

several seconds

 

 

Note :

 

 

5 to 15 cm

• During setting operation , to exit from the setting

 

(2 to 6 inches)

mode, press any of the DIVICE buttons.

3

While “LEARN” is displayed, press the

4

While “SEL” is flickering, on this remote

ENTER button.

control, press the button corresponding to

 

the function to be learned.

 

 

Example) If the function to be learned is playback,

 

 

 

press the PLAY( ) button.

• Then “SEL” is flickering.

 

 

 

 

 

 

 

 

• If “SEL” goes off, start again from the above step .

 

 

 

 

• Then “READY” is displayed.

 

 

 

 

Note:

 

 

 

 

 

• You cannot program a function into some buttons

 

 

such as DEVICE, MACRO and LIGHT buttons.

 

 

 

 

 

 

5

While “READY” is displayed, on the other

6

While “SEL” is flickering, repeat the above

remote control, press the button of the

steps and to program all the

function to be learned.

commands you want to the buttons on this

 

 

 

remote control under the same device mode.

• If the command has been learned successfully,

To exit from the setting mode, press any of the

“OK” is displayed and then “SEL” is flickering.

• If “ERROR” is displayed and then “SEL” is

DEVICE buttons.

flickering, it means that for some reason the

 

 

 

 

 

 

 

 

command was not learned. In this case, repeat the

 

Repeat the above steps to to program

above steps and .

7

the commands from a different remote

Notes :

 

control.

 

 

 

 

 

• If an incorrect signal has been sent or, in some

 

 

 

 

 

 

 

 

cases, the command from other remote control

8

Operate the newly programmed buttons to

simply cannot be learned.

make sure the learning function was

• In some “ERROR” cases, the remote controls just

performed properly.

need to be moved closer together or farther apart.

 

 

 

 

ENGLISH

21

Image 21
Contents 865 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component in 1 Video 1, Component in 2 Video Component video input default settingsVideo Digital input default settingsConnecting System Control Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementMain room Another roomRoom Room 2 connectionsConnecting Microphone Dolby PL II Music Parameter Front Panel ControlsRemote Sensor Fluorescent DisplayFluorescent Display LCD Screen Universal Remote ControlsDevice to be Controlled Function Table of the Numbered ButtonsLoading Batteries Remote Control Operation RangeUsing Functions of Remote Control Entering a setup codeLearn Delete Macro Code Punch Searching a setup code Remote controls Learning mode Programing the commands from otherErasing all the commands Erasing the programmed commandProgrammed under a device mode From one buttonOperating a macro function Programming a macro functionTo erase a macro program To change a macro programAudio Delete TV Programing a punch-through functionCD Delete DVD VCR AUX TV Delete SAT Cable VCROperating a punch-through function Erasing the programmed puch-through functionVOL Delete Play CH English Volume UP/DOWN Buttons Room 2 Remote ControlsListening to a Program Source OperationsBefore operation Tuner CD AUXWhen CD, AUX or Video 1~ Video 4 is selected Adjusting the tone bass and trebleDigital Analog Muting the sound Listening with the headphones Surround modes Surround SoundTheater Front L/R Center PL II Music Enjoying Surround Sound2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Compressing the dynamic rangeDolby Digital sources only Correcting or clearing a label Entering a labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration English Down When selecting the Speaker DistanceWhen selecting the Virtual Speaker Setup When selecting the Subwoofer When selecting the Crossover When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupTo confirm the results, press the Cursor Left /RIGHT When selecting the Digital Input Setup Setting the System SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup When selecting the Video 2 OUT When the DC Trigger mode is set to On When selecting the DC Trigger SetupWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Surround Mode is selected When the Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideSpecifications Amplifier SectionDigital Audio Section Setup Code Table SSS RCATMK CCESTS KLHMEI NSC ABCHTS SATMCS DKKNSM QED865

R-865 specifications

The Sherwood R-865 is a remarkable audio receiver that encapsulates the essence of home audio entertainment. Belonging to the renowned Sherwood brand, this model is a perfect blend of vintage aesthetics and modern engineering, making it a prized addition for audiophiles and casual listeners alike.

At the heart of the Sherwood R-865 lies its powerful amplification section, designed to deliver exceptional sound quality and maintaining audio fidelity across various frequencies. The receiver supports 5.1 channel surround sound, making it an ideal choice for those who enjoy immersive audio experiences in their home theater setups. With a power output of up to 100 watts per channel, the R-865 can easily drive a variety of speaker systems, resulting in detailed sound reproduction that brings movies, music, and games to life.

One of the standout features of the R-865 is its advanced digital signal processing capabilities. This technology not only enhances audio clarity but also ensures that users can enjoy an optimized sound experience tailored to their room's acoustics. The inclusion of multiple sound modes further allows listeners to choose settings that suit different genres of music or types of content, whether it be movies, music, or sports.

Connectivity is another strong point for the Sherwood R-865. It offers a variety of inputs, including HDMI, optical, and coaxial ports, ensuring compatibility with a wide range of sources such as Blu-ray players, gaming consoles, and streaming devices. Additionally, it features built-in Bluetooth technology, allowing users to stream their favorite songs directly from smartphones or tablets without the hassle of wires.

The receiver's user interface is designed with convenience in mind. The LCD display makes it easy to navigate through settings and inputs, while the remote control provides users with extensive control options from the comfort of their couch. For those who appreciate the aesthetics of home audio equipment, the Sherwood R-865 also sports a timeless design with clean lines and a classic finish that complements any home décor.

Moreover, the R-865 offers a robust equalizer feature, enabling users to fine-tune audio outputs to match their unique listening preferences. The receiver also includes various safety features such as short-circuit protection and thermal overload safeguards, ensuring reliable operation over long periods.

In summary, the Sherwood R-865 audio receiver packs a punch with its state-of-the-art audio technologies, versatile connectivity options, and user-friendly design. Whether you’re throwing a movie night or hosting a listening party, this receiver stands ready to deliver an unparalleled audio experience that everyone can enjoy.