DeLonghi DEGLSC24SS warranty Selecting F/C on the Display

Page 15

SELECTING °F/°C ON THE DISPLAY

1.Turn the oven selector knob to a cooking function (i.e. BAKE).

2.Press key 5 on the programmer to reduce the temperature until you reach the min- imum value (120 °F/50 °C).

3.With °F/°C flashing on the display press key 5 again (if °F/°C is not flashing press key 4 before pressing key 5) until OFF appears on the display.

4.Keep key 4 pressed for about 3/5 seconds until the display changes from °C to °F or vice versa. During selection °C or °F is flashing.

5.When OFF apears again on the display turn the selector knob to OFF position; the selection to °C or °F has been completed.

SETTING THE COOKING (ONLY FOR THE COOKING FUNCTIONS)

The temperature set is shown on the electronic programmer display and can be varied, with 5 °F (5 °C) intervals, by means of the programmer keys.

During the cooking the oven temperature (°F or °C) is measured by a sensor inside the cavity and is shown on the programmer display until setted temperature is reached. If setted temperature is less than inside oven temperature, the display shows the setted temperature.

1.SELECTING THE COOKING FUNCTION

Turn the selector knob to the cooking function required

The pre-set temperature appears on the programmer display. °F or °C flashes on the display for 3 seconds. The heating elements start cooking immediately.

2.SETTING THE COOKING TEMPERATURE

The temperature can be changed when °F or °C is flashing on the display

2a. If °F or °C is not flashing press key 4 of the programmer.

2b. Press key 6 to increase the temperature or key 5 to reduce it.

The maximum temperature which can be set is 480 °F (250 °C) while the minimum temperature is 120 °F (50 °C).

Note: When °F or °C becomes steady the value shown on the display indicates the oven cavity temperature until setted temperature is reached. If setted temperature is less than inside oven temperature, the display shows the setted temperature.

Caution: If a temperature below the minimum value (120 °F or 50 °C) is set the system switches off automatically and OFF appears.

In this case repeat the procedure from point 2.

3.SWITCHING OFF

Turn the selector knob to position OFF (oven OFF). The programmer display shows the time.

➀

I

I

I

 

I

I

 

I

I

 

I

I

 

 

I

I

 

I

I

 

 

➁

5

➂

5

➃

4

➄

 

 

Oven programmer

Oven function selector knob

➀

 

I

I

I

I

 

I

 

 

I

 

I

 

 

I

 

I

 

 

 

 

 

I

 

I

I

I

 

 

 

 

 

 

➁

4

5

6

 

2a 2b

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Electric Range ALL Ranges can TIP Dear Customer Replacement Parts Electrical Grounding InstructionsElectrical Requirement Important Precautions and Recommendations Control Panel FeaturesVitroceramic Cooking HOB Never obstruct the slots on the backguardDouble Cooking Zone Rear left zone How to use the vitroceramic hobVitroceramic HOB Cooking ZonesCooking Zones Power Indicator Light fig Cooking Zones Residual Heat IndicatorHints for Safe USE of the Hobs To USE the Warming Drawer How to use the warmer drawerGeneral Features Using the Warming Drawer for the First TimeBetween LO and HI Temperature SelectorUsing the Oven for the First Time How to use the self cleaning ovenSelecting the Functions fig Oven Light this is not a cooking functionDefrosting Frozen Foods this is not a cooking function Traditional Convection Cooking Important Notes Self Cleaning Function this is not a cooking functionSelecting F/C on the Display Turn the oven selector knob to a cooking function i.e. BakeTurn the selector knob to the cooking function required Press pushbutton 3 on the programmer to start the cycle HOW to Start the Self Cleaning CycleF0.00 with Auto flashing Problems on Starting and During the Self Cleaning CycleSteady door Door with Auto flashingFunction selector has been turned to any cooking function HOW to Stop the Self Cleaning CycleWhat to do When the Self Cleaning Cycle has Finished Turn the function selector to OFF oven OFFAbnormal Situations AND/OR Operation Problems During cooking or the self cleaning cycleF0.00 appears during the self cleaning cycle Cooking Different Dishes AT the Same Time Cooking Advice SterilizationRegeneration RoastingStep Broiling Description of the light symbols How to use the electronic programmerSetting the Time Audible SignalDuring cooking TimerSetting SEMI-AUTOMATIC CookingStarting cooking Automatic CookingExamples of Programming Automatic Cooking Cancelling a SET ProgrammeCleaning and maintenance Replacing the Oven Light fig Oven Shelf Installation and RemovalFitting the Warmer Drawer fig Removing the Warmer Drawer figRemoving the Oven Door DO’S and do NOT’S For Your SafetyPage Cod ß3
Top Page Image Contents