GE JGAS02 Using the oven for broiling, Safety Instructions How to Set Your Oven for Broiling

Page 15

Using the oven for broiling.

ge.com

Broiling is cooking food by direct heat from above the food. Most fish and tender cuts of meat can be broiled. Follow these steps to keep spattering and smoking to a minimum.

Your range has a compartment below the oven for broiling. A specially designed broiler pan allows dripping fat to drain away from the food.

Both the oven door and broiler compartment drawer should be closed during broiling.

Safety Instructions

How to Set Your Oven for Broiling

You can change the distance of the food from the heat source by positioning the broiler rack in the broiler compartment:

–A(bottom of broiler

compartment).

–B(center of broiler compartment).

–C(top of broiler compartment). Most broiling should be done in position A.

Preheat the broiler for best results.

If the meat has fat or gristle around the edge, cut vertical slashes through it about 2 inches apart, but don’t cut into the meat. We recommend that you trim the fat to prevent excessive smoking, leaving a layer about 1/8 inch thick.

Close the oven door and broiler compartment drawer.

Turn the OVEN TEMP knob to BROIL.

Turn most foods once during cooking. Time foods for about one- half the total cooking time, turn food, then continue to cook to preferred doneness.

Turn the OVEN TEMP knob to OFF. Remove the broiler pan from the broiler rack and serve the food immediately. Leave the pan outside the range to cool.

Operating Instructions Care and Cleaning Installation

Broiler Compartment

The broiler pan is held in place in the broiler rack.

To remove the broiler pan:

Gently pull forward on the drop down broiler door.

Pull the broiler rack with pan forward until the rack stops. Grasp the broiler pan and remove it from the broiler rack.

To replace the broiler pan:

Slide the broiler pan onto the rack and push both the broiler pan and the rack all the way into the broiler compartment.

Close the broiler door.

Instructions Troubleshooting Tips

Use of Aluminum Foil

Never cover the oven bottom with aluminum foil.

You can use aluminum foil to line your broiler pan and broiler grid. However, you must mold the foil tightly to the pan and cut slits in the foil to open all slots in the grid.

Aluminum foil may also be used to catch a spillover. To do so, place a small sheet of foil on a lower shelf several inches below the food.

Never entirely cover a shelf with aluminum foil. This will disturb the heat circulation and result in poor baking.

15

Consumer Support

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 183D9542P005 Pub Number Ran24 Gas gesWhat to do if YOU Smell GAS Ge.com Safety Instructions Operating Instructions CareInstallation of the range section Cook Meat and Poultry THOROUGHLY… Surface Burners Operating Instructions Installation InstructionsSurface Lighting Instructions for Electric Ignition Models Using the gas surface burnersInstallation Instructions Care and Cleaning InstructionsInstructions Operating Top of Range Cookware How to Select Flame SizeUsing the oven Oven Shelf Positions Oven VentsType of margarine will affect baking performance Using the oven for baking Cakes Cookies SafetyCare and Cleaning Don’t Peek PiesHow to Set the Oven For Roasting Using the oven for roastingAdjust the oven thermostat-Easy to do yourself Safety InstructionsUse of Aluminum Foil Using the oven for broilingSafety Instructions How to Set Your Oven for Broiling Broiler CompartmentComments Broiling GuideTips Consumer Support Care and cleaning of the rangeLift-Up Cooktop Burner GratesOven Shelves and Broiler Rack Cleaning Operating Instructions SafetyBurners Control Panel and KnobsTo remove Cleaning the Oven BottomCleaning Installation Instructions Broiler Compartment Removable Oven BottomInside of door Instructions Safety Broiler Pan and GridLift-Off Oven Door To remove the door800.626.2002 Porcelain Oven Interior SafetyPainted Surfaces Do not use a steel wool pad it will scratch the surfaceBefore YOU Begin Commonwealth of MassachusettsMaterials YOU MAY Need For Your SafetyTools YOU will Need Part IncludedInstallation Safety Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASFlexible Connector Recommended GAS and Electric Supply LocationHookup Example Light the Pilots Seal the OpeningsFor Natural Gas Adjust the Oven Burner AIR Shutter if NecessaryAdjust the Surface Burner Pilots if Necessary If the Range has Electric IgnitionFor LP Gas If Adjustment is NecessaryQuality of Flames Replace Oven PartsInstall the ANTI-TIP Device Level the Range⁄ 8 ″ When ALL Hookups are Completed Mobile Home InstallationModel and Serial Number Location Before you call for service… We Will Replace Gas Range WarrantyWhat is Not Covered Care and CleaningReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

JGAS02 specifications

The GE JGAS02 is an advanced gas turbine designed to meet the growing demand for efficient and reliable energy solutions. With a focus on performance and sustainability, the JGAS02 incorporates a series of cutting-edge technologies that enhance its operational capabilities while reducing its environmental footprint.

One of the standout features of the JGAS02 is its high efficiency rating. The turbine boasts an advanced airfoil design that optimizes airflow and enhances combustion efficiency. This results in reduced fuel consumption and lower emissions, making it an ideal choice for power generation in a world increasingly focused on clean energy solutions.

The JGAS02 utilizes a sophisticated control system that allows for precise monitoring and management of its operation. This system is equipped with predictive analytics, enabling operators to anticipate maintenance needs and minimize downtime. This not only increases the reliability of the turbine but also extends its operational lifespan, providing significant cost savings over time.

Another key characteristic of the JGAS02 is its versatility. It can operate with a variety of fuels, including natural gas, biogas, and even liquid fuels, allowing it to adapt to different market needs and regulatory environments. This flexibility makes it a popular choice for both industrial applications and power plants seeking to diversify their energy sources.

In terms of technology, the JGAS02 features state-of-the-art cooling systems that enhance turbine performance while protecting critical components from high temperatures. Proprietary materials and coatings are employed to ensure durability and longevity in demanding operating conditions.

Moreover, the JGAS02's modular design simplifies maintenance and upgrades, making it easier for operators to implement enhancements as technology evolves. This attention to future-proofing aligns with GE’s commitment to providing long-term value to its customers.

Overall, the GE JGAS02 represents a significant advancement in gas turbine technology. With its blend of high efficiency, operational reliability, and environmental sustainability, it is well-positioned to meet the challenges of modern energy production while supporting a transition to a cleaner energy future.
Top Page Image Contents