GE JGAS02 owner manual Removable Oven Bottom, Cleaning the Oven Bottom, To remove, To replace

Page 19

ge.com

Safety

Knurled screw

(on some

models)

Removable Oven Bottom

First remove the shelves from the oven. The oven bottom lifts from the front.

To remove:

On models so equipped, remove the knurled screw in the front of the oven bottom.

Grasp each side of the oven bottom and push it back.

Lift the front up and pull it out of the oven.

To replace:

Grasp each side of the oven bottom and guide its rear tabs into the slots in the back of the oven.

Lower the oven bottom and pull it forward until it is secure under the front oven floor edge.

On models so equipped, replace the knurled screw in the front of the oven bottom.

NOTE: If the oven bottom is replaced incorrectly, it may warp and cause undesirable baking results.

Instructions Operating Instructions Care

Cleaning the Oven Bottom

The oven bottom has a porcelain enamel finish.

To make cleaning easier, protect the oven bottom from excessive spillovers by placing a cookie sheet on the shelf below the shelf you are cooking on. This is particularly important when baking a fruit pie or other foods with high acid content. Hot fruit fillings or foods that are acidic in content, such as tomatoes or sauerkraut, and sauces with vinegar or lemon juice, may cause pitting and damage to the porcelain enamel surface and should be wiped up immediately.

To protect the oven bottom surface, place a piece of aluminum foil slightly larger than the baking dish on the shelf below to catch any boilovers. It should not completely cover the shelf as this would cause uneven heat in the oven. Aluminum foil should not be placed on the oven bottom.

If a spillover does occur on the oven bottom, allow the oven to cool first. You can clean the bottom with soap and water, a mild abrasive cleanser, soap-filled scouring pads or an oven cleaner following package directions.

and Cleaning Installation Instructions

Broiler Compartment

The broiler pan is held in place in the broiler rack.

To remove the broiler pan:

Gently pull forward on the drop down broiler door.

Pull the broiler rack with pan forward until the rack stops. Grasp the broiler pan and remove it from the broiler rack.

To replace the broiler pan:

Slide the broiler pan onto the rack and push both the broiler pan and the rack all the way into the broiler compartment.

Close the broiler door.

If a spillover occurs in the broiler compartment, allow the compartment to cool first. You can clean the compartment with soap and water, a mild abrasive cleanser, soap-filled scouring pads or an oven cleaner following package directions.

Troubleshooting Tips Consumer Support

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 183D9542P005 Pub Number Ran24 Gas gesWhat to do if YOU Smell GAS Ge.com Safety Instructions Operating Instructions CareInstallation of the range section Cook Meat and Poultry THOROUGHLY… Surface Burners Operating Instructions Installation InstructionsSurface Lighting Instructions for Electric Ignition Models Using the gas surface burnersInstallation Instructions Care and Cleaning InstructionsInstructions Operating Top of Range Cookware How to Select Flame SizeUsing the oven Oven Vents Oven Shelf PositionsType of margarine will affect baking performance Using the oven for baking Cakes Cookies SafetyCare and Cleaning Don’t Peek PiesHow to Set the Oven For Roasting Using the oven for roastingAdjust the oven thermostat-Easy to do yourself Safety InstructionsUse of Aluminum Foil Using the oven for broilingSafety Instructions How to Set Your Oven for Broiling Broiler CompartmentComments Broiling GuideTips Consumer Support Care and cleaning of the rangeLift-Up Cooktop Burner GratesOven Shelves and Broiler Rack Cleaning Operating Instructions SafetyBurners Control Panel and KnobsTo remove Cleaning the Oven BottomCleaning Installation Instructions Broiler Compartment Removable Oven BottomInside of door Instructions Safety Broiler Pan and GridLift-Off Oven Door To remove the door800.626.2002 Porcelain Oven Interior SafetyPainted Surfaces Do not use a steel wool pad it will scratch the surfaceBefore YOU Begin Commonwealth of MassachusettsMaterials YOU MAY Need For Your SafetyTools YOU will Need Part IncludedInstallation Safety Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASRecommended GAS and Electric Supply Location Flexible ConnectorHookup Example Light the Pilots Seal the OpeningsFor Natural Gas Adjust the Oven Burner AIR Shutter if NecessaryAdjust the Surface Burner Pilots if Necessary If the Range has Electric IgnitionFor LP Gas If Adjustment is NecessaryQuality of Flames Replace Oven PartsLevel the Range Install the ANTI-TIP Device⁄ 8 ″ Mobile Home Installation When ALL Hookups are CompletedModel and Serial Number Location Before you call for service… We Will Replace Gas Range WarrantyWhat is Not Covered Care and CleaningReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

JGAS02 specifications

The GE JGAS02 is an advanced gas turbine designed to meet the growing demand for efficient and reliable energy solutions. With a focus on performance and sustainability, the JGAS02 incorporates a series of cutting-edge technologies that enhance its operational capabilities while reducing its environmental footprint.

One of the standout features of the JGAS02 is its high efficiency rating. The turbine boasts an advanced airfoil design that optimizes airflow and enhances combustion efficiency. This results in reduced fuel consumption and lower emissions, making it an ideal choice for power generation in a world increasingly focused on clean energy solutions.

The JGAS02 utilizes a sophisticated control system that allows for precise monitoring and management of its operation. This system is equipped with predictive analytics, enabling operators to anticipate maintenance needs and minimize downtime. This not only increases the reliability of the turbine but also extends its operational lifespan, providing significant cost savings over time.

Another key characteristic of the JGAS02 is its versatility. It can operate with a variety of fuels, including natural gas, biogas, and even liquid fuels, allowing it to adapt to different market needs and regulatory environments. This flexibility makes it a popular choice for both industrial applications and power plants seeking to diversify their energy sources.

In terms of technology, the JGAS02 features state-of-the-art cooling systems that enhance turbine performance while protecting critical components from high temperatures. Proprietary materials and coatings are employed to ensure durability and longevity in demanding operating conditions.

Moreover, the JGAS02's modular design simplifies maintenance and upgrades, making it easier for operators to implement enhancements as technology evolves. This attention to future-proofing aligns with GE’s commitment to providing long-term value to its customers.

Overall, the GE JGAS02 represents a significant advancement in gas turbine technology. With its blend of high efficiency, operational reliability, and environmental sustainability, it is well-positioned to meet the challenges of modern energy production while supporting a transition to a cleaner energy future.
Top Page Image Contents