Rotel Comprehensive Guide for RB 976 Six Channel Power Amplifier
Page 8

SIX CHANNEL POWER AMPLIFIER RB-976

If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip back the insulation from the end of each conductor. Be careful not to cut into the wire strands. Un- screw (turn counterclockwise) the binding post hexagonal thumb- screws. Place the connector lug or wire around the binding post shaft. Turn the hexagonal thumbscrews clockwise to clamp the connector lug or wire firmly in place.

Note: Be sure there are no loose wire strands that could touch adjacent wires or connectors.

Troubleshooting

Most difficulties in audio systems are the result of incorrect con- nections, or improper control settings. If you encounter problems, isolate the area of the difficulty, check the control settings, deter- mine the cause of the fault and make the necessary changes. If you are unable to get sound from the RB-976, refer to the sugges- tions for the following conditions:

Bridged Mono Operation

[See Figure 3 for bridged operation connection illustration.]

The channel pairs of the RB-976 can be “bridged”. In this configu- ration the single channel produces a massive 150 watts! This fea- ture allows you to increase the overall power output of your system by bridging the channel pairs of the RB-976 and adding a second RB-976 that also has bridged channel pairs. Or one of the RB-976 channel pairs may be bridged to drive a monophonic sub- woofer. Note however that when one of the RB-976 channel pairs is bridged the speaker connected to it must have an impedance of 8 ohms or more.

Note: Turn off all the system components before you change any signal connections or the setting of the Input Selector Switches.

To bridge one of the RB-976 channel pairs move the Input Selector Switch for that channel to the “Bridged” position.

Front Panel Power Indicator Is Not Lit

No main power to the RB-976. Check the front panel power switch. Make sure that it is set to the on position. Check AC power connections at the amplifier and the AC outlet.

Fuse Replacement

If everything checks out correctly and you still cannot get the am- plifier to turn on, the internal power fuse may have blown. If you believe this has happened, contact your authorized Rotel dealer to get the fuse replaced.

No Sound

If the amp is getting AC power, but is producing no sound, check the Channel and Bridged Mono indicator lights on the front panel. Then check all input and output connections to be sure they are correct. Finally check the connections to, and the control settings of, the associated components.

Input Connection

When using one of the RB-976 channel pairs in bridged mono mode, connect the cable from the preamplifier or signal processor output to the left input of the channel pair. No connection is made to the right input.

Note: It is possible to link inputs B and/or C while A is in the Bridged Mode. Both left and right inputs are used for A.

Bridged Speaker Connection

When using one of the RB-976 channel pairs in bridged mono mode, the wire to the speakers is connected to the positve termi- nals of the left and right channels. Connect the wire that goes to the postive terminal of the speaker to the positve terminal of the left channel of the channel pair. Connect the wire that goes to the negative terminal of the speaker to the positve terminal of the right channel of the channel pair. No connections are made to the negative terminals.

4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents RB-976 Risk of Electric Shock Do not Open SIX Channel Power Amplifier RB-976 Preamplifier or Signal Processor Few Precautions EnglishAbout Rotel Getting StartedAC Power and Controls Input Configuration and Connection Speaker ConnectionTroubleshooting Bridged Mono OperationFrançais Table des matièresEmplacement Un mot sur RotelPréliminaire Quelques précautions à prendreAlimentation et commutateur général Configuration et branchement des sources Branchement des enceintesFonctionnement en mono en mode ponté DépannageInhaltsverzeichnis Sicherheits- und WarnhinweiseZu dieser Anleitung DeutschDie Firma Rotel Netzspannung und Bedienung Eingangskonfiguration und EingangsanschlüsseLautsprecher Brückenschaltung Bei StörungenNumeri in grassetto fanno riferimento alle illustrazioni ItalianoIndice Alcune parole sulla Rotel Per cominciareAlcune precauzioni PosizionamentoCollegamento e configurazione di ingresso Collegamento alla rete e controlliCollegamento dei diffusori Configurazione mono a ponte Ricerca dei guastiContenido Español Acerca de RotelPara Empezar Algunas PrecaucionesAlimentación y Control Circuitería de ProtecciónConmutador 1 e Indicador Luminoso de Puesta en Marcha Entrada de Corriente EléctricaConexiones y Configuración de Entrada Conexión de las Cajas AcústicasProblemas y Posibles Soluciones Funcionamiento en Modo Monofónico PuenteadoSpecifications Fiche techniqueCaracterísticas Técnicas Technische DatenRB-976

RB-976 specifications

The Rotel RB-976 represents an exceptional entry in the realm of high-performance amplifier technology. Renowned for its robust power output, high-quality sound reproduction, and solid construction, it has earned a distinguished place among audiophiles and home theater enthusiasts alike. This power amplifier is particularly celebrated for its ability to deliver deep, dynamic audio across a wide range of frequencies.

One of the standout features of the RB-976 is its remarkable power output, capable of delivering 100 watts per channel into 8 ohms and 130 watts per channel into 4 ohms. This ensures that the amplifier can drive a variety of speakers with ease, making it a versatile choice for both music listening and home theater applications. The amplifier's ability to sustain high power levels makes it suitable for driving demanding speaker systems without distortion.

The RB-976 utilizes advanced Class AB amplification technology. This design combines the efficiency of Class A with the output power benefits of Class B, resulting in a sound that is rich, warm, and engaging. The amplifier’s linearity and low distortion characteristics ensure that listeners experience audio fidelity that is true to the original recording.

Another key feature is the use of a toroidal transformer. This high-quality power supply contributes to the rich dynamic range by providing a clean and stable power source. The transformer design minimizes electromagnetic interference, further enhancing audio clarity. Coupled with its large capacitors, the RB-976 can handle transient peaks in music and movie soundtracks effortlessly, preserving the integrity of the audio signal.

In terms of build quality, the RB-976 is constructed with a sturdy chassis designed to minimize vibration and enhance durability. Its discreet design allows for seamless integration into any audio or home theater setup. The amplifier includes both XLR and RCA inputs, providing flexibility in connection options to accommodate different equipment.

Thermal management is another area where the RB-976 excels, with an effective heat dissipation system that ensures the amplifier remains cool during extended listening sessions. The robust heatsinks maintain optimal operating temperatures, which contributes to the long-term reliability of the unit.

In conclusion, the Rotel RB-976 is a powerful and versatile amplifier that embodies quality sound and durable construction. With its Class AB topology, advanced power supply, and thoughtful design, it remains a compelling choice for audiophiles seeking to enhance their audio playback experiences. Whether for music or home cinema, the RB-976 delivers a captivating listening experience that leaves a lasting impression.
Top Page Image Contents