West Bend QUIKSERVE instruction manual Cleaning Your Drip Coffeemaker

Page 9
CLEANING YOUR DRIP COFFEEMAKER

LCD Back-Light Setting Function: Upon initial connection to a power source or the resumption of power after a power failure the default setting is Auto-off. The blue back-light display will turn off after approximately one minute if the unit is off. The blue back-light display will remain on while the coffeemaker is brewing or in keep warm mode. The blue back-light display can be set to “Always on” by pressing the HOUR and MINUTE buttons at the same time for approximately five seconds. Performing this function again when “Always on” is set will change the display back to Auto-off.

CLEANING YOUR DRIP COFFEEMAKER

1.Switch coffeemaker off and unplug from electrical outlet. Allow the entire unit to cool before cleaning.

2.Remove and discard used grounds and disposable filter from the brew basket.

3.Clean the brew basket, carafe and cover in a solution of warm water and mild liquid soap. Rinse thoroughly. These parts may also be cleaned in an automatic dishwasher, top rack only.

4.If there is water left in the water reservoir, empty through the top opening of the unit by turning upside down over a sink.

5.The exterior of the coffeemaker can be wiped clean with a damp cloth after it has been unplugged and the base is cooled.

Do not clean the inside of the water reservoir with a cloth or paper towel. This may leave particles in the chambers that may clog small openings in your coffeemaker. Rinse with cold water periodically.

Decalcify the Drip Coffeemaker periodically. See the “Decalcifying Your Drip Coffeemaker” section in this manual.

9

Image 9
Contents QUIKSERVE PROGRAMMABLE COFFEEMAKER HEAT PRECAUTIONS IMPORTANT SAFEGUARDSELECTRICITY PRECAUTIONS PRECAUTIONS FOR USE AROUND CHILDREN SAVE THESE INSTRUCTIONSUSING YOUR DRIP COFFEEMAKER - FIRST USE GLASS CARAFE CAUTIONSUSING YOUR DRIP COFFEEMAKER - PREPARING COFFEE USING YOUR COFFEEMAKER - CONTROLS AND FEATURES Use PROG/AUTO button to select the Keep Warm Hours setting function. The PROG/AUTO indicator light and the last set programmed 1-digit Keep Warm Hour LCD will be flashing. Note The default value will be the last programmed Keep Warm Hours setting. If the displayed value is desired, press PROG/AUTO to confirm and set or pressing the HOUR button will adjust the keep warm hour setting from 1 to 5 hours. Each pressing of the HOUR button will increase the keep warm time by one hour. After the 5 hours maximum setting, the keep warm time will cycle back to 1hour The CLOCK will be flashing CLEANING YOUR DRIP COFFEEMAKER DECALCIFYING YOUR DRIP COFFEEMAKER PROBLEMS AND CAUSESAppliance 1 Year Limited Warranty PRODUCT WARRANTYREPLACEMENT PARTS Valid only in USA and CanadaPage Manuel d’instructions MACHINE À CAFÉ QUIKSERVE PROGRAMMABLEPRÉCAUTIONS LIÉES À LA CHALEUR MISES EN GARDE IMPORTANTESPRÉCAUTIONS LIÉES À L’ÉLECTRICITÉ CONSERVEZ CES INSTRUCTIONS 5.Fermez le couvercle du réservoir AUTOMATIQUE DU CAFÉ SÉLECTION DE LA FONCTION À PROGRAMMERPROGRAMMATION DE LA FONCTION DE MAINTIEN AU CHAUD PROGRAMMATION DE L’HORLOGE DE 24 HEURESPRÉPARATION MANUELLE DU CAFÉ FONCTIONS SUPPLÉMENTAIRES PRÉPARATION AUTOMATIQUE DU CAFÉNETTOYAGE DE LA CAFETIÈRE PROBLÈMES ET CAUSES DÉTARTRAGE DE LA CAFETIÈREGARANTIE DU PRODUIT Garantie de l’appareil limitée à 1 anPIÈCES DÉTACHÉES Page Manual de instrucciones CAFETERA PROGRAMABLE QUIKSERVEPRECAUCIONES DE CALENTAMIENTO PRECAUCIONES IMPORTANTESPRECAUCIONES ELÉCTRICAS PRECAUCIONES DE USO CERCA DE NIÑOS CONSERVE ESTAS INSTRUCCIONESPRECAUCIONES SOBRE LA JARRA DE VIDRIO USO DE LA CAFETERA DE GOTEO - PRIMER USOUSO DE LA CAFETERA DE GOTEO - PREPARACIÓN DE CAFÉ CÓMO USAR LA CAFETERA - CONTROLES Y FUNCIONES Use el botón PROG/AUTO para seleccionar la función que ajusta las Horas de Mantenimiento en Caliente. La luz indicadora PROG/AUTO y el último ajuste programado de las Horas de Mantenimiento en Caliente de 1 dígito en la pantalla de cristal líquido destellarán. Nota El valor predeterminado será el último ajuste programado de Horas de Mantenimiento en Caliente. Si el valor mostrado es deseado, pulse PROG/AUTO para confirmarlo y fijarlo o pulse el botón HOUR hora para ajustar la horas de Mantenimiento en Caliente entre 1 a 5 horas. Cada pulsación del botón HOUR aumentará en una hora el tiempo de mantenimiento en caliente. Después del ajuste máximo de 5 horas, el tiempo de mantenimiento en caliente regresará de vuelta a 1 hora Cada pulsación del botón PROG/AUTO seleccionará de manera alterna entre encender o apagar la Preparación Automática. El pulsar el botón PROG/AUTO cuando la Preparación Automática esté apagada enciende esta última, el icono AUTO en la pantalla de cristal líquido destella, y la pantalla indica durante 3 segundos la hora estable programada para la preparación automática. Al final de los 3 segundos la Preparación Automática se activa y el icono Auto en la pantalla de cristal líquido se mantiene encendido constantemente y la pantalla entra en la modalidad de reloj. Nota Si la Preparación Automática está activada encendida, el presionar el botón PROG/AUTO cancela la Preparación Automática y el icono AUTO en la pantalla de cristal líquido se apaga LIMPIEZA DE LA CAFETERA DE GOTEO DESCALCIFICACIÓN DE LA CAFETERA DE GOTEO PROBLEMAS Y CAUSASREPUESTOS GARANTÍA DEL PRODUCTO