Motion Computing C5 manual Using Standby, To put the computer on Standby

Page 32

The following illustration shows the Power Options Properties open to the Power Schemes tab.

Using Standby

Standby is a state in which the display and hard disks turn off, so that the computer uses less power. When you want to use the computer again, it comes out of standby quickly, although you may have to log on again.

Use standby to save power when you will be away from the computer for a short time while working. Because Standby does not save your data to the hard disk, a power failure while on Standby can cause you to lose unsaved information.

To put the computer on Standby

1.Open Motion Dashboard to the Power panel (page 18).

2.For Power Button, select Standby.

3.To put the computer on Standby, press the power button.

To turn the computer back on, press the power button.

30	Chapter 3 Using the Motion C5

Image 32

Contents User’s Guide AuthenTec is a registered trademark of AuthenTec, Inc Getting Started Overview FrontRight side Top sideBack side Setting up the Motion C5 Tablet PC TutorialsTo calibrate the digitizer Under Pen, tap Calibrate DigitizerGet familiar with the Motion C5 Features2 Pen Status lightsFront panel buttons Windows Security buttonSecurity DisplayFingerprint reader Microphones CameraDataGuard Rfid reader Docking connectorSpeaker Bar code scanner optional UPC-A UPC-EBattery Wi-Fi 802.11a/b/g wirelessBluetooth wireless Power adapter Features Using the Motion C5 Using Motion Dashboard To start Motion DashboardUsing the pen Configuring pen optionsTo configure pen options Tap the Pen & Button Options buttonUsing Tablet PC Input Panel Using the cameraTo start Input Panel To use the cameraConfiguring front panel buttons To configure the front panel buttonsTap Pen and Button Options Tap the Tablet Buttons tab Tap ChangeChanging the screen orientation Using the displayAdjusting the display brightness Changing the display rotation sequence To change the rotation sequenceUsing the bar code scanner To use the bar code scannerUsing the Rfid reader To use the Rfid readerTo set up the angle of acceptance Using the built-in microphonesSetting up the angle of acceptance To set up the skew angle Using speech recognitionSetting up the skew angle Setting up speech recognition To set up speech recognitionSelect Dictation or Commands Starting speech recognitionUsing power management Using Standby To put the computer on StandbySelect Enable Hibernation To put the computer on Hibernate Using HibernateTo enable Hibernation Using the battery Checking battery powerTo check the remaining battery power To check the battery gaugeTo remove the battery Charging the batteryRemoving and replacing the battery To swap batteries Swapping the batteryTo replace the battery Battery and power management tips Disposing of used batteriesUsing Motion OmniPass and the fingerprint reader Capturing a fingerprintTo start Motion OmniPass To capture a fingerprintPage Fingerprint reader tips Using password replacement Using the password wizardTo register passwords To run the password wizardSetting up strong logon security To enable strong logon securityTo configure authentication rules Logging on to a remembered siteUsing Windows Security Center Setting a Bios password Setting up users and passwordsSetting up Windows user accounts Enabling or disabling Wi-Fi Using Wi-Fi 802.11a/b/gSetting up a hard disk drive HDD password Enabling or disabling Bluetooth Using BluetoothSetting up a Wi-Fi connection Setting up a Bluetooth device To set up a Bluetooth connectionIf the device is not discovered… Bluetooth wireless tipsFinding additional software Care and Maintenance General careView Anywhere display Standard displayCleaning in a health care environment Disinfecting proceduresCleaning the fan cover Cleaning solutionsTo clean the fan cover Training and documentation considerationsCleaning the fingerprint reader To clean the fingerprint readerTraveling with the Motion C5 Replacing pen tipsOrdering new pens To replace the pen tipFAA Wireless air travel requirement Using Acronis True Image in WindowsRestoring data Traveling by airUsing Acronis Startup Recovery Manager Creating a backup archiveCreating a bootable disk Tap Remove Acronis OEM Zone Removing the Acronis OEM ZoneTo remove the OEM Zone Care and Maintenance Troubleshooting Computer will not enter Hibernation modeComputer does not turn on Computer does not shut downBattery does not last very long less than three hours Display goes black while the C5 is still turned onLost data while swapping batteries Desktop area is larger than the C5 displayC5 does not respond to the pen I am using Expand Display adaptersPointer on the screen does not align with the pen Function button does not workNo sound is coming from the speakers Computer seems to be operating more slowly than usualFrequently asked questions How do I adjust the C5 for left-handed use? SpecificationsWarranty and insurance programs Service and support Appendix a Troubleshooting and Support

Related manuals

Manual 86 pages 47.69 Kb