CMA Dishmachines L-1X16 manual Receiving and Installation, Electrical, Plumbing, Post Instructions

Page 7

Getting Started

2.2.Receiving and Installation

The dishwasher is shipped from the factory in a corrugated box on a wooden pallet. The installation guidelines give a systematic procedure for setting up the machine.

1.Start by removing the box and packaging material. Check for the following component parts:

A.Drain Screen:

The Wash Tank Scrap Screen is shipped inside the wash cavity of the machine. This screen must be in place during operation. It has been designed to perform two basic functions:

•Strain water that is circulating through the spray arms and pump assembly.

•A basket to catch heavy solids or broken glass that may plug the impeller.

B.Spray Arms

The end caps on the spray arms have been taped to protect them in shipping. Remove the tape from the spray arm end caps.

C.Tube Stiffeners:

The tube stiffeners must be used to prevent the feed tubes from curling up inside the chemical pail allowing the tip to rise out of the chemical. Remove the tie-wraps securing the tube stiffeners to the dishmachine to free them up for use. Be careful not to remove any of the tie-wraps securing the tube bundle.

2.Set the machine in place and, using the leg adjusters, level from side-to-side and front-to- back.

2.2.1. Electrical*

A 20-amp, 115 volt, 60 Hz dedicated circuit must be used to supply electrical power to the L-1X or L-1X16 Dishmachine (see specification sheet page 1). The power connection must be such that there is sufficient length of flexible conduit or power cord to permit the machine to be moved for cleaning.

2.2.2. Plumbing*

The machine is equipped with a gate valve with a ½” female NPT connection located at the lower left-hand corner (facing the back) of the machine. A 140°F water line should be plumbed to this point. The water line used must be of sufficient length and flexibility to permit the machine to be moved for cleaning.

A 1” male NPT fitting is provided for the drain connection on the discharge port of the diverter valve (lower, right-hand corner of machine). This fitting may be removed and user provided hardware may be used if necessary to facilitate compliance with local plumbing codes. Code requires that the drain discharge provides an air gap no less than 1” or two pipe diameters, whichever is greater, above the flood level rim of an approved floor drain.

2.2.3. Post Instructions

Mount the wall chart provided in a conspicuous place and instruct the operators on proper cleaning and operation of the L-1X and L-1X16. The instruction chart is also provided as an appendix to this manual (see appendix).

*Electrical and plumbing connections must be made by a qualified person who will comply with all available Federal, State, and Local Health, Electrical, Plumbing and Safety codes

MODEL L-1X & L-1X16 Installation & Operations Manual Rev. 1.14

Page6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 7 0 0 K N O T T a V E N U E Model L-1X & L-1X16Table of Contents L-1X & L-1X16 Specifications100 110 L-1X and L-1X16 Operational CycleSee .1.1 Cam Adjustment Getting Started Getting StartedIntroduction to the L-1X and L-1X16 Post Instructions Receiving and InstallationElectrical PlumbingInstallers Checklist General Initial SetupOperation OperationWater Pump Proper FillingPump Cavitation Cam Adjustment MaintenanceMaintenance Timer assemblyQuick service guide Troubleshooting Maintenance Maintenance Addendum Addendum for Machines Installed in the City of ChicagoAppendix a Operator & Cleaning Instructions Electrical Diagram

L-1X16, L-1X specifications

CMA Dishmachines L-1X and L-1X16 are state-of-the-art commercial dishwashers designed to streamline dishwashing processes in various foodservice environments. Recognized for their innovative technology and robust construction, these machines are ideal for restaurants, hotels, and institutional kitchens.

One of the standout features of the CMA L-1X and L-1X16 is their high efficiency. With a capacity to handle up to 40 racks per hour, these models significantly reduce the time spent on washing dishes and improve overall kitchen productivity. Their rapid cycle times ensure that clean dishes are always available, enhancing service speed and minimizing wait times during busy hours.

The L-1X and L-1X16 are designed with advanced wash arm technology, featuring multiple spray zones that ensure thorough cleaning of all dishware. The powerful pump provides exceptional water pressure, ensuring that even the toughest stains are removed with ease. In addition, the units include a built-in booster heater, which raises water temperatures to optimal levels for effective sanitization, complying with health and safety regulations.

Another key characteristic of these dishmachines is their user-friendly interface. The intuitive control panel allows operators to select wash cycles effortlessly, making it easy for staff to operate the machines without extensive training. The digital readout indicates cycle time and wash temperature, providing transparency and ensuring operational efficiency.

The L-1X and L-1X16 models are constructed from durable stainless steel, guaranteeing longevity and resistance to the wear and tear of daily commercial use. Their compact design maximizes workspace efficiency, making them suitable for kitchens with limited space. Additionally, the machines are designed for easy access to internal components, facilitating maintenance and reducing downtime.

Energy efficiency is a priority for CMA Dishmachines, and both the L-1X and L-1X16 models reflect this commitment. These dishwashers consume less water and energy compared to other models in the market, ultimately reducing operating costs and contributing to a more sustainable kitchen environment.

In summary, the CMA Dishmachines L-1X and L-1X16 are highly efficient commercial dishwashers that combine advanced technology, user-friendly features, and durable construction. They are designed to meet the rigorous demands of the foodservice industry while maintaining a focus on efficiency and sustainability. For establishments looking to enhance their dishwashing capabilities, these models represent a cutting-edge solution.
Top Page Image Contents