Dynex 91000051 manual Installation Unpacking, Materials Provided

Page 21

Unpacking

Unpacking

Chapter 2 Installation

Unpacking

Materials Provided

The main carton contains the instrument. The contents of this carton are listed below:

Article	Quantity
Opsys MW™ System	1
Instrument Power Cable	1
Cleaning Wire, Aspirate	1
Cleaning Wire, Dispense	1
Instrument Configuration Report	1
User’s Guide	1
Declaration of Conformity	1
Wash Head, 1 x 8 or 1 x12	1
Plate Holder	1

A sub-carton contains the wash container and waste container assemblies. The contents of this carton are listed below:

Article	Quantity
Wash Container Assembly	1
Waste Container Assembly	1

Opsys MW™ User’s Guide

13

Image 21

Contents Please read carefully before using the Opsys MW Opsys MW Microplate WasherUser’s Guide This manual is published by DYNEX Technologies, Inc Part No. 91000051, Revision BDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703Warranty and Special Provisions Limited Warranty Page Table of Contents Table of ContentsChapter 2 Installation Chapter 3 ConfigurationChapter 8 Service Chapter 7 TroubleshootingIndex Opsys MW User’s GuideAbout this Manual About this ManualThis manual gives you the information needed to This page is intentionally left blank Chapter 1 Introduction DescriptionDescription Programming Wash Head Wash HeadDescription Wash Head Position Wash Head PositionsDescription Dispense HeightWaste Wash FluidDescription Features FeaturesFeatures Dimensions and Weight SpecificationsPower Requirements SpecificationsStandards Input RangesPlate Setup Assay ProgrammingWarning Labels Warning LabelsLabel Description Warning Labels Chapter 2 Installation Unpacking Materials ProvidedUnpacking To unpack the components Hardware Components Hardware ComponentsKeypad. The keypad is used by the operator to select commands and enter wash parameters Figure 3. Rear View of the Opsys MW System Connectors at the rear of the Opsys MW system are shown in FigurePositioning the Instrument Positioning the InstrumentInstalling the Wash Head Installing the Wash HeadInstalling the Wash Container To install the Wash ContainerInstalling the Wash Container Installing the Waste Container To install the Waste Container and Foam/Aerosol TrapInstalling the Waste Container Turning on the System Turning on the SystemSETUP PROGRAM 1. Connect the Opsys MW to the laboratory electrical supply outletChapter 3 Configuration The Keypad The Keypad7 8 9 Purpose “Cancel” keyScroll keys If you are entering or editing information , aKeys AlphanumericThe numeral shown on the key is displayed by pressing the key once. If the key is pressed two toConfigure the Instrument SETUPMenus MenusThe PROGRAM Menu The SETUP MenuConfiguring the System Configuring the SystemCommand CLEANSpecifying the Wash Head Specifying Plate Parameters To specify parameters for a plate type Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed Sweep height? SHOW Configuring the System Displaying the Software Version Note Refer to page 74 for additional pump calibration instructions Specifying the Pump ParametersSelecting Clean Configuring the System Wash Protocol Operations Chapter 4 Wash Protocols Wash Protocol OperationsOperation PurgeDispense SoakFill Creating a New Wash Protocol Specifying the HeaderCreating a New Wash Protocol To create a new wash protocol header Select plate 2 DYNEX1 7. Re-enter the password and press ENTER. The display will readVariable strips? YESNO 9. If YES is selected, the display will read Constant timing? YESNOSelect option MOVE PURGE Specifying Wash Cycle Operations To specify a Purge To specify a Move cycle Note An Aspirate or Dispense must be To specify an Aspiration within a MoveNote A Dispense or Aspirate must be performed within a Move cycle To specify a Dispense within a Move6. Press ENTER. The display will read Cycles? To specify a Soak within a Move To specify a Fill within a Move Note A volume ranging from 50 to 300 microliters can be enteredNote A Fill must be performed within a Move cycle Select option SOAK FILL Ending a MOVE Cycle2. Scroll right to display the next selection. The display will read Select option END LOOP 3. Select END LOOP. The display will readTo specify a Soak outside of a Move Select option SOAK END 2. Select END. The display will read 1 NAME01 To specify the End of the wash protocolModifying a Wash Protocol To modify a wash protocolModifying a Wash Protocol MOVE To modify a wash operation To delete a wash operation To insert a wash operation Copying a Wash Protocol To copy a wash protocolCopying a Wash Protocol Overwrite test? NO YESNO 8. Select YES. The display will read 7 NAME04 SETUP PROGRAMPreparation Chapter 5 Washing a PlateTo empty the waste container PreparationTo refill the wash container Washing a Plate To wash a plateWashing a Plate Washing a Plate Daily maintenance Chapter 6 Routine Maintenance Routine Maintenance ProceduresWeekly maintenance Six month maintenanceAs required maintenance To clean the system Cleaning and DecontaminationCleaning and Decontamination To decontaminate the systemCleaning the Containers To empty and clean the waste containerCleaning the Containers Replacing the Tubing To replace the dispense tubingReplacing the Tubing To replace the vacuum tubing To replace the waste tubing Pump Calibration Calibration ProtocolPump Calibration 8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page Pump Calibration Operational Problems Chapter 7 Troubleshooting Operational ProblemsSymptom ResolutionSymptom waste container is X Motor Home High Waste LevelZ Motor Home Test Too Large isTo remove the wash head assembly Chapter 8 Service Service ProceduresTo clean the wash head assembly To replace the wash head assemblySpare Parts AccessoriesMajor Assemblies HardwareReturning a Washer for Service To return a Washer for serviceReturning a Washer for Service EQUIPMENT DECLARATION EQUIPMENT IN TRANSITCERTIFICATE OF DECONTAMINATION Suggested decontamination methodsContact DYNEX Technologies Contact DYNEX TechnologiesDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA Index Indexvariable strips, 41 warning labels, 11 Wash Container, 5