Dynex 91000051 manual Washing a Plate, Preparation, To empty the waste container

Page 71

Preparation

Preparation

Chapter 5 Washing a Plate

Once the parameters for at least one plate type and one wash protocol have been set, the system can be used to wash a plate.

Preparation

The only preparation that is required is to check the fluid levels in the Wash Container and the Waste Container. Service the containers if necessary.

To empty the waste container:

1.Unscrew the cap of the Waste Container. Lay the cap and level sensor assembly on a paper towel.

2.Discard the waste in accordance with local regulations.

3.Rinse the waste container with deionized water. Discard the rinse water.

Note: If desired, the waste container can be disinfected with a 10% (v/v) solution of household bleach in water.

4.Place the level sensor and tube back into the Waste Container and screw the cap on.

Opsys MW™ User’s Guide

63

Image 71

Contents User’s Guide Please read carefully before using the Opsys MWOpsys MW Microplate Washer Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703 Part No. 91000051, Revision BThis manual is published by DYNEX Technologies, Inc DYNEX Technologies 14340 Sullyfield CircleWarranty and Special Provisions Limited Warranty Page Chapter 3 Configuration Table of ContentsTable of Contents Chapter 2 InstallationOpsys MW User’s Guide Chapter 7 TroubleshootingChapter 8 Service IndexThis manual gives you the information needed to About this ManualAbout this Manual This page is intentionally left blank Description Chapter 1 IntroductionDescription Programming Description Wash HeadWash Head Dispense Height Wash Head PositionsWash Head Position DescriptionWaste Wash FluidOpsys MW User’s Guide Features FeaturesOpsys MW User’s Guide Specifications SpecificationsDimensions and Weight Power RequirementsAssay Programming Input RangesStandards Plate SetupLabel Description Warning LabelsWarning Labels Opsys MW User’s Guide Unpacking Chapter 2 Installation UnpackingMaterials Provided To unpack the components Hardware Components Hardware ComponentsKeypad. The keypad is used by the operator to select commands and enter wash parameters Figure 3. Rear View of the Opsys MW System Connectors at the rear of the Opsys MW system are shown in FigurePositioning the Instrument Positioning the InstrumentInstalling the Wash Head Installing the Wash HeadInstalling the Wash Container Installing the Wash ContainerTo install the Wash Container Installing the Waste Container Installing the Waste ContainerTo install the Waste Container and Foam/Aerosol Trap 1. Connect the Opsys MW to the laboratory electrical supply outlet Turning on the SystemTurning on the System SETUP PROGRAM7 8 9 Chapter 3 Configuration The KeypadThe Keypad If you are entering or editing information , a “Cancel” keyPurpose Scroll keyspressing the key once. If the key is pressed two to AlphanumericKeys The numeral shown on the key is displayed byMenus SETUPConfigure the Instrument MenusThe PROGRAM Menu The SETUP MenuCLEAN Configuring the SystemConfiguring the System CommandSpecifying the Wash Head Specifying Plate Parameters To specify parameters for a plate type Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed Sweep height? SHOW Opsys MW User’s Guide Displaying the Software Version Note Refer to page 74 for additional pump calibration instructions Specifying the Pump ParametersSelecting Clean Opsys MW User’s Guide Purge Chapter 4 Wash Protocols Wash Protocol OperationsWash Protocol Operations OperationFill DispenseSoak Creating a New Wash Protocol Creating a New Wash ProtocolSpecifying the Header To create a new wash protocol header 9. If YES is selected, the display will read Constant timing? YESNO 7. Re-enter the password and press ENTER. The display will readSelect plate 2 DYNEX1 Variable strips? YESNOSelect option MOVE PURGE Specifying Wash Cycle Operations To specify a Purge To specify a Move cycle Note An Aspirate or Dispense must be To specify an Aspiration within a MoveNote A Dispense or Aspirate must be performed within a Move cycle To specify a Dispense within a MoveOpsys MW User’s Guide To specify a Soak within a Move Note A Fill must be performed within a Move cycle To specify a Fill within a MoveNote A volume ranging from 50 to 300 microliters can be entered Select option END LOOP 3. Select END LOOP. The display will read Ending a MOVE CycleSelect option SOAK FILL 2. Scroll right to display the next selection. The display will readTo specify a Soak outside of a Move Select option SOAK END 2. Select END. The display will read 1 NAME01 To specify the End of the wash protocolModifying a Wash Protocol Modifying a Wash ProtocolTo modify a wash protocol MOVE To modify a wash operation To delete a wash operation To insert a wash operation Copying a Wash Protocol Copying a Wash ProtocolTo copy a wash protocol Overwrite test? NO YESNO 8. Select YES. The display will read 7 NAME04 SETUP PROGRAMPreparation Chapter 5 Washing a PlatePreparation To empty the waste containerTo refill the wash container Washing a Plate Washing a PlateTo wash a plate Opsys MW User’s Guide Six month maintenance Chapter 6 Routine Maintenance Routine Maintenance ProceduresDaily maintenance Weekly maintenanceAs required maintenance To decontaminate the system Cleaning and DecontaminationTo clean the system Cleaning and DecontaminationCleaning the Containers Cleaning the ContainersTo empty and clean the waste container Replacing the Tubing Replacing the TubingTo replace the dispense tubing To replace the vacuum tubing To replace the waste tubing Pump Calibration Pump CalibrationCalibration Protocol 8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page Opsys MW User’s Guide Resolution Chapter 7 Troubleshooting Operational ProblemsOperational Problems SymptomProbable Cause waste container is Test Too Large is High Waste LevelX Motor Home Z Motor HomeTo replace the wash head assembly Chapter 8 Service Service ProceduresTo remove the wash head assembly To clean the wash head assemblyHardware AccessoriesSpare Parts Major AssembliesReturning a Washer for Service Returning a Washer for ServiceTo return a Washer for service Suggested decontamination methods EQUIPMENT IN TRANSITEQUIPMENT DECLARATION CERTIFICATE OF DECONTAMINATIONDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA Contact DYNEX TechnologiesContact DYNEX Technologies Index Indexvariable strips, 41 warning labels, 11 Wash Container, 5