Dynex 91000051 manual Specifying the Wash Head, Configuring the System

Page 37

Specifying the Wash Head

Configuring the System

Specifying the Wash Head

The HEAD command allows the installed wash head to be specified:

1. Select SETUP. The display will read:

Select option

HEAD PLATE

2.Select HEAD. The current wash head selection is displayed in the upper line:

Wash head?	8
8

If needed, scroll right to view the remaining selection:

Wash head?	8
12

3.Select the desired option using the function key. After the selection is made, the display will again read:

Select option

HEAD PLATE

Opsys MW™ User’s Guide

29

Image 37

Contents Opsys MW Microplate Washer Please read carefully before using the Opsys MWUser’s Guide This manual is published by DYNEX Technologies, Inc Part No. 91000051, Revision BDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703Warranty and Special Provisions Limited Warranty Page Table of Contents Table of ContentsChapter 2 Installation Chapter 3 ConfigurationChapter 8 Service Chapter 7 TroubleshootingIndex Opsys MW User’s GuideAbout this Manual About this ManualThis manual gives you the information needed to This page is intentionally left blank Description Chapter 1 IntroductionDescription Programming Wash Head Wash HeadDescription Wash Head Position Wash Head PositionsDescription Dispense HeightWaste Wash FluidThis page is intentionally left blank Features FeaturesThis page is intentionally left blank Dimensions and Weight SpecificationsPower Requirements SpecificationsStandards Input RangesPlate Setup Assay ProgrammingWarning Labels Warning LabelsLabel Description This page is intentionally left blank Materials Provided Chapter 2 Installation UnpackingUnpacking To unpack the components Hardware Components Hardware ComponentsKeypad. The keypad is used by the operator to select commands and enter wash parameters Figure 3. Rear View of the Opsys MW System Connectors at the rear of the Opsys MW system are shown in FigurePositioning the Instrument Positioning the InstrumentInstalling the Wash Head Installing the Wash HeadTo install the Wash Container Installing the Wash ContainerInstalling the Wash Container To install the Waste Container and Foam/Aerosol Trap Installing the Waste ContainerInstalling the Waste Container Turning on the System Turning on the SystemSETUP PROGRAM 1. Connect the Opsys MW to the laboratory electrical supply outletThe Keypad Chapter 3 Configuration The Keypad7 8 9 Purpose “Cancel” keyScroll keys If you are entering or editing information , aKeys AlphanumericThe numeral shown on the key is displayed by pressing the key once. If the key is pressed two toConfigure the Instrument SETUPMenus MenusThe PROGRAM Menu The SETUP MenuConfiguring the System Configuring the SystemCommand CLEANSpecifying the Wash Head Specifying Plate Parameters To specify parameters for a plate type Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed Sweep height? SHOW Select option HEAD PLATE Displaying the Software Version Note Refer to page 74 for additional pump calibration instructions Specifying the Pump ParametersSelecting Clean This page is intentionally left blank Wash Protocol Operations Chapter 4 Wash Protocols Wash Protocol OperationsOperation PurgeSoak DispenseFill Specifying the Header Creating a New Wash ProtocolCreating a New Wash Protocol To create a new wash protocol header Select plate 2 DYNEX1 7. Re-enter the password and press ENTER. The display will readVariable strips? YESNO 9. If YES is selected, the display will read Constant timing? YESNOSelect option MOVE PURGE Specifying Wash Cycle Operations To specify a Purge To specify a Move cycle Note An Aspirate or Dispense must be To specify an Aspiration within a MoveNote A Dispense or Aspirate must be performed within a Move cycle To specify a Dispense within a Move6. Press ENTER. The display will read Cycles? To specify a Soak within a Move Note A volume ranging from 50 to 300 microliters can be entered To specify a Fill within a MoveNote A Fill must be performed within a Move cycle Select option SOAK FILL Ending a MOVE Cycle2. Scroll right to display the next selection. The display will read Select option END LOOP 3. Select END LOOP. The display will readTo specify a Soak outside of a Move Select option SOAK END 2. Select END. The display will read 1 NAME01 To specify the End of the wash protocolTo modify a wash protocol Modifying a Wash ProtocolModifying a Wash Protocol MOVE To modify a wash operation To delete a wash operation To insert a wash operation To copy a wash protocol Copying a Wash ProtocolCopying a Wash Protocol Overwrite test? NO YESNO 8. Select YES. The display will read 7 NAME04 SETUP PROGRAMPreparation Chapter 5 Washing a PlateTo empty the waste container PreparationTo refill the wash container To wash a plate Washing a PlateWashing a Plate This page is intentionally left blank Daily maintenance Chapter 6 Routine Maintenance Routine Maintenance ProceduresWeekly maintenance Six month maintenanceAs required maintenance To clean the system Cleaning and DecontaminationCleaning and Decontamination To decontaminate the systemTo empty and clean the waste container Cleaning the ContainersCleaning the Containers To replace the dispense tubing Replacing the TubingReplacing the Tubing To replace the vacuum tubing To replace the waste tubing Calibration Protocol Pump CalibrationPump Calibration 8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page This page is intentionally left blank Operational Problems Chapter 7 Troubleshooting Operational ProblemsSymptom ResolutionSymptom waste container is X Motor Home High Waste LevelZ Motor Home Test Too Large isTo remove the wash head assembly Chapter 8 Service Service ProceduresTo clean the wash head assembly To replace the wash head assemblySpare Parts AccessoriesMajor Assemblies HardwareTo return a Washer for service Returning a Washer for ServiceReturning a Washer for Service EQUIPMENT DECLARATION EQUIPMENT IN TRANSITCERTIFICATE OF DECONTAMINATION Suggested decontamination methodsContact DYNEX Technologies Contact DYNEX TechnologiesDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA Index Indexvariable strips, 41 warning labels, 11 Wash Container, 5