English Directions for use, Rating plate

Hyundai BD-143GB English Directions for use, Installation Choice of position for installation

English

Directions for use

In the following, you will find all the important information for the use of your appliance.

The instructions for use apply to several models, which is why details of the information may differ according to the type of the appliance.

1Installation (Choice of position for installation)

Strictly avoid high ambient temperatures and direct sunlight. We advise you to place your appliance in a cool, well aired, dry room. Installation in the immediate vicinity of a heat source (heating, oven etc.) is highly inappropriate (increased compressor performance would be necessary and, as a result, power consumption would be considerably higher).

If the installation near a heat source cannot be avoided, a suitable insulation plate must be fitted between the appliance and the heat source (do not use asbestos), or the following minimum distances must be observed:

from gas or electric cooker	3	cm
from radiator or oven	5	cm

from a wall, piece of furniture or

another appliance

2 cm

Never obstruct the ventilation grille

Larger chest freezers are equipped with a ventilation grille (F) located below on one side. These appliances can be placed directly against a wall or a piece of furniture but not with the side protected with the ventilation grille.

Freezers without ventilation grille

Leave sufficient space between the rear of the appliance and the wall to ensure that outward flow of warm air is able to escape.

The appliance must be placed horizontally and on a levelled base. Only this way can an impeded circuit of the refrigerant and optimum function be ensured.

IMPORTANT!

Leave the appliance stand in the final position for at least 2 hours before switching it on, so that the refrigerant circuit stabilises and no operating problems occur.

The odour which is typical of all new appliances is easy to remove.

Thoroughly clean the interior compartment with a mixture of lukewarm water and vinegar.

Do not use washing liquids, sharp or granular cleaning implements, or any cleaning products containing soda.

Before connecting the appliance, make sure that the inner area – especially the corners – is absolutely dry.

Danger warning

Depending on its composition, the refrigerant is easily inflammable. The refrigerant circuit is hermetically sealed and the density has been subject to repeated tests.

An improper intervention can cause acute fire hazard.

Instruction for use

Omit any mechanical influence on the cooling system, especially on the following accessible parts in the compressor chamber (L):

Rear wall condenser or skin condenser (R)

Compressor (P) (motor)

Capillary tube (Q)

Drying filter (N)

Interventions on the cooling system must be carried out by professional and authorised personnel only.

IMPORTANT!

Escaping refrigerant can injure your eyes.

In the event of eye contact with the refrigerant, wash your eyes instantly under plenty of running water and call/consult an eye specialist immediately.

2Rating plate

The rating plate (with technical data) is located on the housing (D) at the rear of the appliance.

Take a note of the technical data

Copy the technical data from the rating plate to here so that it is at any time readily available, without having to move the appliance

Model/Type …………….…………………………

Net capacity ………………….……………litres

Operating voltage ………………….……...…...V-50Hz

Maximum absorbed power(W)..……………….Watt

Safety (A) ……………….....………………......Amp

Power consumption………………………….....kWh/24h

Freezing capacity…………………………….....kg/24h

3Connection to power supply

Your appliance must be connected to a power socked with grounded connection, which is conform to the respective standards and has been installed by an authorised specialist.

Before you connect the plug of the appliance with the power socket, make absolutely sure that

the voltage (V) on the appliance’s data-plate corresponds with that of your mains.

If the voltage differs, notify the after-sales-service or your dealer immediately, and do not on any account connect the appliance to the mains.

4temperature selection (Thermostat) (FIG.4)

To prevent temperature being accidentally modified, the control is intentionally resistant to turning. To vary the setting, we recommend to use a coin or screwdriver.

To switch on: Turn the control to the right

adjust temperature to the level you require, between:

-Min. (slight cooling) and

-max. (lowest temperature)

BD-143GB, BD-100GB, BD-203GAA, BD-103GB, BD-103GAA specifications

The Hyundai BD-318A, BD-203GB, BD-146G, BD-143GAA, and BD-146GAA are part of Hyundai's prestigious lineup of construction equipment, especially tailored to meet the demands of modern construction and heavy-duty applications. Each model boasts distinct features and technologies that enhance performance, safety, and efficiency.

The Hyundai BD-318A is a robust machine known for its powerful performance in various conditions. It is equipped with a strong engine that provides high torque and excellent fuel efficiency. The BD-318A’s advanced hydraulic system ensures smooth operation and precise control, allowing operators to perform complex tasks with ease. The spacious cabin design enhances operator comfort, featuring ergonomic controls and excellent visibility.

Moving on to the BD-203GB, this model stands out for its versatility and adaptability. It is engineered for both urban and off-road environments, making it ideal for diverse construction projects. The BD-203GB features an advanced telematics system that monitors machine performance and health in real time. This technology not only helps in preventative maintenance but also optimizes operational efficiency by providing operators with critical data.

The BD-146G is designed with productivity in mind. With its enhanced lift capacity and stability, this model is perfect for lifting heavy loads with confidence. The cutting-edge suspension system further ensures smooth operation over rough terrain. Safety is prioritized with features such as a rollover protective structure (ROPS) and advanced braking systems that give operators peace of mind while working.

Similarly, the BD-143GAA reflects Hyundai's commitment to safety and efficiency. It incorporates a state-of-the-art engine that complies with the latest emissions regulations, making it an environmentally friendly choice. The updated hydraulic technology enhances its overall performance and reduces operational costs.

Lastly, the BD-146GAA combines power and efficiency, boasting a rugged design suited for tough job sites. This model excels in fuel efficiency, reducing the total cost of ownership while delivering exceptional performance. With user-friendly controls and an intuitive dashboard, it allows operators to focus on their work without distractions.

In summary, the Hyundai BD-318A, BD-203GB, BD-146G, BD-143GAA, and BD-146GAA represent the pinnacle of engineering in construction equipment. Their main features, advanced technologies, and specific characteristics contribute to enhanced performance, safety, and overall efficiency, making them indispensable tools for modern construction projects. The continuous innovations by Hyundai ensure that their machines not only meet but exceed the expectations of their users.