Jet Tools JMS-12SCMS manual Compound Miter Saw Safety

Page 7

Compound Miter Saw Safety

Specific safety instructions for this compound miter saw

1.Do not operate the miter saw until it is completely assembled and installed according to these instructions.

2.If you are not thoroughly familiar with the operation of miter saws, seek guidance from your supervisor, instructor or other qualified person.

3.Always hold the work firmly against the fence and table.

4.Do not perform any operation free hand (use clamp wherever possible).

5.Keep hands out of the path of the saw blade. If the workpiece you are cutting would cause your hands to be within 8-3/4 in. of the saw blade, the workpiece should be clamped in place before making the cut.

6.Be sure the blade is sharp, runs freely and is free of vibration.

7.Allow the motor to come up to full speed before starting a cut.

8.Keep the motor air slots clean and free of chips or dust.

9.Always make sure all handles are tight before cutting, even if the table is positioned in one of the positive stops.

10.Be sure both the blade and the collar are clean and the arbor bolt is tightened securely.

11.Use only blade collars specified for your saw.

12.Never use blades larger in diameter than 12 inches.

13.Never apply lubricants to the blade when it is running.

14.Always check the blade for cracks or damage before operation. Replace a cracked or damaged blade immediately.

15.Never use blades recommended for operation at less than 4200 RPM.

16.Always keep the blade guards in place and use at all times.

17.Never reach around the saw blade.

18.Make sure the blade is not contacting the workpiece before the switch is turned ON.

19.Important: After completing the cut, release the trigger and wait for the blade to stop before returning the saw to the raised position.

20.Make sure the blade has come to a complete stop before removing or securing the workpiece, changing the workpiece angle or changing the angle of the blade.

21.Never cut metals or masonry products with this tool. This miter saw is designed for use on wood and wood-like products.

22.Never cut small pieces. If the workpiece being cut would cause your hand or fingers to be within 8-3/4 in. of the saw blade the workpiece is too small.

23.Provide adequate support to the sides of the saw table for long work pieces.

24.Never use the miter saw in an area with flammable liquids or gases.

25.Never use solvents to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material.

26.Shut off the power before servicing or adjusting the tool.

27.Disconnect the saw from the power source and clean the machine when finished using.

28.Make sure the work area is clean before leaving the machine.

29.Should any part of your miter saw be missing, damaged, or fail in any way, or any electrical component fail to perform properly, lock the switch and remove the plug from the power supply outlet. Replace missing, damaged, or failed parts before resuming operation.

7

Image 7
Contents Part No. M-707120 Benchtop Series Model No. JMS-12SCMS174315 Walter Meier Manufacturing IncMore Information Warranty and ServiceTable of Contents Page Page Page Compound Miter Saw Safety Cut Type Miter Angle Bevel Angle Cutting Capacity Introduction SpecificationsCutting Capacity JMS-12SCMSExtension Cords Power Supply and Motor SpecificationsElectrical Electrical RequirementsFeatures Shipping Contents Releasing the Cutting Head AssemblyInstalling the Dust Bag Unlocking the Slide CarriagePower Cord Storage Clips Installing the Safety Hold-down ClampSaw Blade Wrench Mounting the Saw Table InsertsRemoving the Blade Installing Blade Bevel Scale Indicators AdjustmentsBevel Stop Adjustments Bevel AdjustmentLeft & Right Bevel Adjustment Right Bevel Positive Stop AdjustmentMiter Scale Indicator Adjustment Adjusting Fence SquarenessMiter Angle Quick-cam Miter Table Lock Adjustment Positive Stop Miter Angle AdjustmentQuick-cam Miter Table Lock Operation Laser Beam Presetting the Cutting DepthRear Support Bar Jammed Material OperationStarting a cut Finishing a cutSliding Fence Removing or Installing the Sliding FenceSliding Carriage System Bevel Cut Miter CutCompound Cuts Bevel Detent Pin for Crown Moldings90º Crosscut Narrow Boards Unlock the carriage lock knob D Slide Cutting Wide BoardsChanging the Belt Cutting Bowed MaterialRough Cutting a Dado Auxiliary Wood FenceCrown Molding Bevel/Miter SettingsBevel Miter Type of Cut Key Setting Procedure Cutting Base MoldingSetting Walls Crown Molding ChartSaw Dust MaintenanceReplacing Carbon Brushes Lower Blade GuardTroubleshooting Operation Troubleshooting MotorTrouble Probable Cause Remedy Parts Ordering Replacement Parts Parts ListIndex No Description Size Qty JMS10SCMS-43 JMS10SCMS-36JMS10SCMS-37 JMS12SCMS-53JMS10SCMS-98 JMS10SCMS-87JMS10SCMS-88 JMS10SCMS-92SB-6MM JMS10SCMS-2 Index No. Part No Description Size QtyJMS10SCMS-99 Assembly Drawing Assembly Drawing Assembly Drawing Wiring Diagram New Sanford Road LaVergne, Tennessee Phone
Related manuals
Manual 1 pages 28.2 Kb

JMS-12SCMS specifications

The Jet Tools JMS-12SCMS is a standout in the world of sliding compound miter saws, designed specifically for professionals and serious hobbyists alike. This sophisticated tool combines power, precision, and versatility, making it an essential addition to any workshop.

At the heart of the JMS-12SCMS is its robust motor, which delivers an impressive 15 amps of power. This strength allows it to handle a wide variety of materials, from hardwoods to softer composites, making it ideal for intricate cuts and heavy-duty applications. With a maximum cutting capacity of 12 inches, the JMS-12SCMS can effortlessly slice through larger workpieces with ease, providing the kind of versatility that woodworkers crave.

One of the primary features of the jet saw is its innovative sliding mechanism. This sliding arm design allows for expanded cutting capacity, so users can achieve precise crosscuts and bevels without the need for additional tools. The smooth glide feature ensures that the saw moves effortlessly along its track, significantly reducing friction and wear.

The JMS-12SCMS also boasts a dual bevel capability, allowing for bevel cuts up to 45 degrees left and right. This feature is particularly useful for complex projects that require intricate angles, giving users the flexibility to make precise adjustments without having to flip the workpiece. Additionally, the miter angle can be adjusted to a range of 60 degrees to the right and 52 degrees to the left, providing a comprehensive cutting range for any project.

For enhanced accuracy, this tool includes an easy-to-read digital display for miter and bevel angles, allowing users to set their cuts with confidence. The built-in laser guide further aids in precision, ensuring that every cut is exactly where it's needed.

Safety is always a priority, and the JMS-12SCMS incorporates several features to keep users protected. The saw’s blade guard effectively shields users from accidental contact with the blade, while the electric brake stops the blade quickly after the trigger is released, minimizing the risk of injury.

In conclusion, the Jet Tools JMS-12SCMS is an exceptional tool that combines robust power, innovative features, and a focus on safety. Its advanced technologies and user-friendly design make it a top choice for those seeking reliability and precision in their woodworking projects. Whether you're a professional contractor or a dedicated DIY enthusiast, the JMS-12SCMS will undoubtedly exceed your expectations.