Jet Tools JMS-12SCMS manual Power Supply and Motor Specifications, Electrical Requirements

Page 9

Electrical

Power Supply and Motor

Specifications

The AC motor used in this saw is a universal, nonreversible type (see Motor in the Specifica- tions section on page 8).

To avoid electrical hazards, fire hazards, or damage to the machine, use proper circuit protection. Your saw is wired at the factory for 120V operation. Connect to a 120V, 15 Amp circuit and use a 15 amp time delay fuse or circuit breaker. If power cord is worn or cut, or damaged in any way, have it replaced immediately to avoid shock or fire.

Electrical Requirements

This machine is double insulated to provide a double thickness of insulation between the user and the machine's electrical system. All exposed metal parts are isolated from the internal metal motor components with protective insulation.

This saw has a plug that looks like the one shown in Figure A.

Figure A

To reduce the risk of electrical shock, this saw has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way; if the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Double insulation does not take the place of normal safety precautions when operating this tool.

To avoid electrocution:

1.Use only identical replacement parts when servicing a tool with double insulation. Servicing should be performed by a qualified technician.

2.Do not use power tools in wet or damp locations or expose them to rain or snow.

Extension Cords

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. The table below shows the correct size to use depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord.

Cord Length

AWG

0 – 25ft

16

5 – 50ft

14

Important: Make certain the receptacle in question is properly grounded. If you are not sure, have a registered electrician check the receptacle.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 174315 Benchtop Series Model No. JMS-12SCMSWalter Meier Manufacturing Inc Part No. M-707120More Information Warranty and ServiceTable of Contents Page Page Page Compound Miter Saw Safety Cutting Capacity Introduction SpecificationsJMS-12SCMS Cut Type Miter Angle Bevel Angle Cutting CapacityElectrical Power Supply and Motor SpecificationsElectrical Requirements Extension CordsFeatures Shipping Contents Installing the Dust Bag AssemblyUnlocking the Slide Carriage Releasing the Cutting HeadInstalling the Safety Hold-down Clamp Power Cord Storage ClipsSaw Blade Wrench Table Inserts Mounting the SawRemoving the Blade Installing Blade Bevel Stop Adjustments AdjustmentsBevel Adjustment Bevel Scale IndicatorsLeft & Right Bevel Adjustment Right Bevel Positive Stop AdjustmentAdjusting Fence Squareness Miter Scale Indicator AdjustmentMiter Angle Positive Stop Miter Angle Adjustment Quick-cam Miter Table Lock AdjustmentQuick-cam Miter Table Lock Operation Presetting the Cutting Depth Laser BeamRear Support Bar Starting a cut OperationFinishing a cut Jammed MaterialRemoving or Installing the Sliding Fence Sliding FenceSliding Carriage System Bevel Cut Miter CutBevel Detent Pin for Crown Moldings Compound Cuts90º Crosscut Narrow Boards Unlock the carriage lock knob D Slide Cutting Wide BoardsRough Cutting a Dado Cutting Bowed MaterialAuxiliary Wood Fence Changing the BeltBevel Miter Type of Cut Key Setting Procedure Bevel/Miter SettingsCutting Base Molding Crown MoldingSetting Walls Crown Molding ChartReplacing Carbon Brushes MaintenanceLower Blade Guard Saw DustTroubleshooting Motor Troubleshooting OperationTrouble Probable Cause Remedy Ordering Replacement Parts Parts List PartsIndex No Description Size Qty JMS10SCMS-37 JMS10SCMS-36JMS12SCMS-53 JMS10SCMS-43JMS10SCMS-88 JMS10SCMS-87JMS10SCMS-92 JMS10SCMS-98SB-6MM Index No. Part No Description Size Qty JMS10SCMS-2JMS10SCMS-99 Assembly Drawing Assembly Drawing Assembly Drawing Wiring Diagram New Sanford Road LaVergne, Tennessee Phone
Related manuals
Manual 1 pages 28.2 Kb

JMS-12SCMS specifications

The Jet Tools JMS-12SCMS is a standout in the world of sliding compound miter saws, designed specifically for professionals and serious hobbyists alike. This sophisticated tool combines power, precision, and versatility, making it an essential addition to any workshop.

At the heart of the JMS-12SCMS is its robust motor, which delivers an impressive 15 amps of power. This strength allows it to handle a wide variety of materials, from hardwoods to softer composites, making it ideal for intricate cuts and heavy-duty applications. With a maximum cutting capacity of 12 inches, the JMS-12SCMS can effortlessly slice through larger workpieces with ease, providing the kind of versatility that woodworkers crave.

One of the primary features of the jet saw is its innovative sliding mechanism. This sliding arm design allows for expanded cutting capacity, so users can achieve precise crosscuts and bevels without the need for additional tools. The smooth glide feature ensures that the saw moves effortlessly along its track, significantly reducing friction and wear.

The JMS-12SCMS also boasts a dual bevel capability, allowing for bevel cuts up to 45 degrees left and right. This feature is particularly useful for complex projects that require intricate angles, giving users the flexibility to make precise adjustments without having to flip the workpiece. Additionally, the miter angle can be adjusted to a range of 60 degrees to the right and 52 degrees to the left, providing a comprehensive cutting range for any project.

For enhanced accuracy, this tool includes an easy-to-read digital display for miter and bevel angles, allowing users to set their cuts with confidence. The built-in laser guide further aids in precision, ensuring that every cut is exactly where it's needed.

Safety is always a priority, and the JMS-12SCMS incorporates several features to keep users protected. The saw’s blade guard effectively shields users from accidental contact with the blade, while the electric brake stops the blade quickly after the trigger is released, minimizing the risk of injury.

In conclusion, the Jet Tools JMS-12SCMS is an exceptional tool that combines robust power, innovative features, and a focus on safety. Its advanced technologies and user-friendly design make it a top choice for those seeking reliability and precision in their woodworking projects. Whether you're a professional contractor or a dedicated DIY enthusiast, the JMS-12SCMS will undoubtedly exceed your expectations.
Top Page Image Contents