Jet Tools JMS-12SCMS manual Presetting the Cutting Depth, Laser Beam, Rear Support Bar

Page 20

Presetting the Cutting Depth

The depth of cut can be preset for even and repetitive shallow cuts.

Referring to Figure 21:

1.Pull hold-down latch (C) out.

2.Flip the stop plate (A) counterclockwise to the left.

3.Adjust the cutting head down (See Cutting Head section) until the teeth of the blade are at the desired depth.

4.While maintaining the cutting head in the desired position, turn the stop knob (B) until it touches the stop plate (A).

5.Recheck the blade depth by moving the cutting head front to back through the full motion of a typical cut along the control arm.

Laser Beam

The laser is turned on with a switch located on the saw handle (C, Fig. 23). When left on indefinitely, a sensor will turn the laser off after 20 minutes. The switch must be reset (turned off for two seconds, then on again) to restart.

The laser has no adjustments and should not require adjustment. If adjustment should become necessary, take the miter saw to an approved service center.

Laser radiation. Avoid direct eye exposure. Always un-plug miter saw from power source before making any adjustments.

Laser Warning Label: Max output <1mW

DIODE LASER: 522-542nm, Complies with 21CFR 1040.10 and 1040. 11.

Figure 21

Rear Support Bar

Do not operate the saw without the rear extension support bar. Failure to comply may result in serious injury!

Loosen the two screws (A, Fig. 22) and extend the rear extension support bar (B, Fig. 22) by sliding it out, then tighten the two screws.

A

B

CAUTION

LASER RADIATION

DO NOT STARE INTO BEAM

MAX OUTPUT <1mW, DIODE LASER 522-542nm

COMPLIES WITH 21CFR 1040.10 AND 1040.11

CLASS II LASER PRODUCT

Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.

The use of optical instruments

with this product will increase eye hazard.

Do not attempt to repair or disassemble the laser. If unqualified persons attempt to repair this laser product, serious injury may result. Any repair required on this laser product should be performed by authorized service center personnel.

Figure 22

20

Image 20
Contents Benchtop Series Model No. JMS-12SCMS 174315Walter Meier Manufacturing Inc Part No. M-707120Warranty and Service More InformationTable of Contents Page Page Page Compound Miter Saw Safety Introduction Specifications Cutting CapacityJMS-12SCMS Cut Type Miter Angle Bevel Angle Cutting CapacityPower Supply and Motor Specifications ElectricalElectrical Requirements Extension CordsFeatures Shipping Contents Assembly Installing the Dust BagUnlocking the Slide Carriage Releasing the Cutting HeadSaw Blade Wrench Installing the Safety Hold-down ClampPower Cord Storage Clips Removing the Blade Table InsertsMounting the Saw Installing Blade Adjustments Bevel Stop AdjustmentsBevel Adjustment Bevel Scale IndicatorsRight Bevel Positive Stop Adjustment Left & Right Bevel AdjustmentMiter Angle Adjusting Fence SquarenessMiter Scale Indicator Adjustment Quick-cam Miter Table Lock Operation Positive Stop Miter Angle AdjustmentQuick-cam Miter Table Lock Adjustment Rear Support Bar Presetting the Cutting DepthLaser Beam Operation Starting a cutFinishing a cut Jammed MaterialSliding Carriage System Removing or Installing the Sliding FenceSliding Fence Miter Cut Bevel Cut90º Crosscut Narrow Boards Bevel Detent Pin for Crown MoldingsCompound Cuts Slide Cutting Wide Boards Unlock the carriage lock knob DCutting Bowed Material Rough Cutting a DadoAuxiliary Wood Fence Changing the BeltBevel/Miter Settings Bevel Miter Type of Cut Key Setting ProcedureCutting Base Molding Crown MoldingCrown Molding Chart Setting WallsMaintenance Replacing Carbon BrushesLower Blade Guard Saw DustTrouble Probable Cause Remedy Troubleshooting MotorTroubleshooting Operation Index No Description Size Qty Ordering Replacement Parts Parts ListParts JMS10SCMS-36 JMS10SCMS-37JMS12SCMS-53 JMS10SCMS-43JMS10SCMS-87 JMS10SCMS-88JMS10SCMS-92 JMS10SCMS-98SB-6MM JMS10SCMS-99 Index No. Part No Description Size QtyJMS10SCMS-2 Assembly Drawing Assembly Drawing Assembly Drawing Wiring Diagram New Sanford Road LaVergne, Tennessee Phone
Related manuals
Manual 1 pages 28.2 Kb

JMS-12SCMS specifications

The Jet Tools JMS-12SCMS is a standout in the world of sliding compound miter saws, designed specifically for professionals and serious hobbyists alike. This sophisticated tool combines power, precision, and versatility, making it an essential addition to any workshop.

At the heart of the JMS-12SCMS is its robust motor, which delivers an impressive 15 amps of power. This strength allows it to handle a wide variety of materials, from hardwoods to softer composites, making it ideal for intricate cuts and heavy-duty applications. With a maximum cutting capacity of 12 inches, the JMS-12SCMS can effortlessly slice through larger workpieces with ease, providing the kind of versatility that woodworkers crave.

One of the primary features of the jet saw is its innovative sliding mechanism. This sliding arm design allows for expanded cutting capacity, so users can achieve precise crosscuts and bevels without the need for additional tools. The smooth glide feature ensures that the saw moves effortlessly along its track, significantly reducing friction and wear.

The JMS-12SCMS also boasts a dual bevel capability, allowing for bevel cuts up to 45 degrees left and right. This feature is particularly useful for complex projects that require intricate angles, giving users the flexibility to make precise adjustments without having to flip the workpiece. Additionally, the miter angle can be adjusted to a range of 60 degrees to the right and 52 degrees to the left, providing a comprehensive cutting range for any project.

For enhanced accuracy, this tool includes an easy-to-read digital display for miter and bevel angles, allowing users to set their cuts with confidence. The built-in laser guide further aids in precision, ensuring that every cut is exactly where it's needed.

Safety is always a priority, and the JMS-12SCMS incorporates several features to keep users protected. The saw’s blade guard effectively shields users from accidental contact with the blade, while the electric brake stops the blade quickly after the trigger is released, minimizing the risk of injury.

In conclusion, the Jet Tools JMS-12SCMS is an exceptional tool that combines robust power, innovative features, and a focus on safety. Its advanced technologies and user-friendly design make it a top choice for those seeking reliability and precision in their woodworking projects. Whether you're a professional contractor or a dedicated DIY enthusiast, the JMS-12SCMS will undoubtedly exceed your expectations.