Saeco Coffee Makers SG200E instruction manual Water circuit filling, Recommended solutions

Page 19

English

6.7.2 Water circuit filling

The machine automatically activates the pump and starts filling the espresso coffee boiler.

IMPORTANT:

Before powering the machine, thus starting the automatic installation:

1.Make sure that the water softener is filled with water and the air bubbles removed.

2.Load the reachable columns of the cup holder.

NOTE:

If the filling of the boiler is not successful, the machine cannot be set into service. A failure message will be shown on the display. Should it be the case, eliminate the cause and reset the error recorded (section 8 ‘Programming and maintenance menu’), then repeat the automatic installation, switching the machine on once again. After a testing phase on start-up, the machine automatically fills the water circuit of the tray equipped with a float and of the brew group boiler. During this stage, the heating element of the boiler remains automatically off. If the machine detects that the boiler is already filled, it passes to the heating stage.

The sequence of operations will be:

-insert the special key in the machine cover switch

-on start-up of the machine, the filling of the tray equipped with a float starts automatically, while the machine carries out the automatic testing phase.

During testing, the following components start up in the given order:

-the brew group, so as to reach the correct start-up position

-the cup holder, so as to load the first cup column into the releasing device.

During the setting-up phase:

-the coffee boiler and the water tank are filled up

-once the water circuit is filled, the heating phase starts up, thus switching on automatically the boiler heating element.

Recommended solutions

When the boiler is completely filled, wash the mixer repeatedly in order to remove possible residues from the hydraulic circuits. NB: see section 8 - Programming and Maintenance menu, in order to start test or cleaning brewing.

-After performing these operations, wait a few minutes for the machine to reach service temperature and make beverages available.

19

Image 19
Contents Type SG200E Operation and MaintenanceMain Parts Table of Contents Introduction to Manual Read General instructions Data Plate Operators requirements Technical SpecificationsContainer Capacity Safety StandardsGeneral safety rules CUP DispenserHandling and transport Handling and StorageStorage Beverage Selection General Technical DescriptionCUP, Sugar and Stirrer Dispensing AVAILABLE’Instant Beverage Brewing Espresso Coffee Brewing Positioning InstallationReceipt Remove the key from the beverage dispensing outlet fig Water system connection Power supply connectionMachine start-up Cleaning and filling of resin- based water softener InstallationWater circuit filling Cleaning the parts in contact with foodstuffs Product loading Container loading Cup loading Label insertionDo not Attempt to Turn Coulumn Manually Stirrer loading Payment system installation on the machine Payment System InstallationRif.1 Payment system installation on the base cabinetKey Down Key 〉 UP Key c Cancel / beverage Programming and Maintenance MenuBeverage Key Down / sugar fig Description of programming and maintenance phase keysKey c Cancel /beverage 01 fig Key e Enter / beverage 05 figContinues System Management Beverage YES Continues Instant KEY= Preselection Price Table Timetable Setting System Management Never Free Functions of the programming menu ResetMinimum temperature Structure of the programming menuPre-grinding Maximum temperatureText Out of Service Wash cycleMultiple beverage StirrerKey Instant Product beforePayment Systems Overpay time Banknote ValueProtocol MultivendCoffee Water Instant productExample Instant waterPrice table Maintenance menu Accessing the maintenance menuBeverage prices Maintenance Error Operational defects Failures Description of maintenance menu messagesMaintenance Error / Message nnReset failed Automatic Error ResetError Log LOG Monitor Operation Method Display MessageSoftware updating WashingBoiler emptying StatisticsCleaning and loading MaintenanceDaily cleaning English Weekly cleaning Week Month SIX MaintenanceProduct loading EveryBrew group maintenance Scheduled and unscheduled maintenanceAdjustments Dose and grinding adjustment Cup releasing device cleaning and adjustment Importante Align the Five SCROLLS’ Align the TWO Arrows References Selection Number Resin regeneration where the water softener is providedInactivity Dismantling Display Messages Error code Messaggio Cause CureMessages during operation Out of service/Failure conditions YES Or coffee stop Beverages State Function Visual Signals LEDOn the CPU card LEDCN1 CN6CN2 CN3On the Power card I/O English English English English English Cod -956-ED

SG200E specifications

The Saeco Coffee Maker SG200E is a remarkable machine that caters to coffee enthusiasts who appreciate both convenience and quality in their brewing experience. With its sleek design and user-friendly interface, the SG200E stands out in the world of automatic coffee makers, ensuring that both novice users and seasoned baristas can enjoy a delicious cup of coffee at the touch of a button.

One of the main features of the Saeco SG200E is its advanced brewing system, which employs cutting-edge technology to enhance the flavor extraction process. The machine uses the patented Saeco Brewing System, allowing users to customize their brew according to their personal taste preferences. This feature ensures that whether you prefer a strong espresso or a milder Americano, the SG200E can deliver the perfect cup every time.

Another significant characteristic of the SG200E is its integrated grinder, equipped with ceramic burrs that grind the beans to an ideal consistency. Ceramic grinders are known for their durability and ability to preserve the rich aromas of the coffee, making them a favorite among coffee aficionados. Users can adjust the grind settings to achieve their desired coarseness, providing them with complete control over their coffee experience.

The Saeco SG200E also features a user-friendly digital display that simplifies navigation and allows for easy programming of your preferred beverages. From selecting the size of your drink to adjusting strength and temperature, the intuitive interface makes it easy for anyone to create their perfect cup.

Additionally, the SG200E is designed with maintenance in mind. Its removable brewing unit and dishwasher-safe components make cleaning a breeze, ensuring that your coffee maker remains in optimal condition without the hassle of complicated upkeep.

The steam wand is another highlight, designed for frothing milk to create delicious cappuccinos and lattes. With its powerful steam output and ease of use, users can achieve barista-quality frothed milk at home, bringing café-style beverages into their kitchen.

In conclusion, the Saeco Coffee Maker SG200E embodies the perfect blend of technology, convenience, and customization. Its advanced brewing system, integrated grinder, user-friendly interface, and maintenance features make it a top choice for anyone seeking to elevate their coffee experience at home. Whether for a single cup or entertaining guests, the SG200E ensures that every brew is a delightful journey into the world of coffee.