Murray 465600x8A manual Attachments, HOW to USE the Throttle Control

Page 15

OPERATION

ATTACHMENTS

This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.

For all pull-behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it.

Do not operate on a slope that is greater than 10 degrees when using a pull-behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer.

HOW TO USE THE THROTTLE CONTROL

Use the throttle control to increase or decrease the speed of the engine.

CAUTION: Always operate the engine with the throttle control in the FAST position. If the engine runs for several minutes at slower than the FAST position, the engine and transmission will overheat and can be damaged.

1.The FAST position is marked with a detent. For normal opera- tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine and transmission, operate the en- gine in the FAST position.

2.For transport and to tow pull behind attachments, control the ground speed with the speed control pedal.

3.The engine governor is set at the factory for maximum perform- ance. Do not adjust the governor to increase the speed of the engine.

HOW TO USE THE BLADE ROTATION CONTROL

The blade rotation control is next to the steering wheel (Figure 5). Use the blade rotation control to engage the blade(s) or to operate a snow thrower attachment.

1.Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position.

2.Move the blade rotation control to the ENGAGE position to rotate the blade(s).

Note: If the engine stops when you engage the blade(s), the seat switch is not activated. Make sure you sit in the middle of the seat. Also, make sure the wire is connected to the seat switch.

3.Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating.

4.Before you ride the unit across a sidewalk or a road, move the blade rotation control to the DISENGAGE position.

WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs.

Disengage

Position

Blade Rotation Control

Engage Position

Figure 5

F-030727L

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly Assembly25x3 17x146 HOW to Install the SeatHOW to Assemble the Steering Wheel 100105417x47Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsHow To Remove The Mulcher Plate HOW to Change the Mulcher PlateGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingHOW to Install the Mower Housing Remove the mower drive belt from the stack pulleyHOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley Remove the primary mower drive belt from the stack pulley HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Assemble the left pulley coverFasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030727L MURRAY, INC. Lawn Mower Central Parts Distributors030727L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Key Part Description Electrical System030727L 030727L 030727L Index Model No Bushel Capacity Model No

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents