Murray 465600x8A HOW to USE the Speed Control Pedal, HOW to Disconnect the Transmission, To 1/2

Page 16

OPERATION

HOW TO USE THE SPEED CONTROL PEDAL

The drive system uses a Hydrostatic Automatic Drive transmission. The Hydrostatic transmission is very easy to operate. This type of drive system does not require a shift lever or a clutch pedal.

The speed and direction of travel is controlled by a single speed control pedal operated with your right foot. Do not use the left brake pedal in normal operation. Only use the left brake pedal to quickly stop in an emergency.

HOW TO DRIVE FORWARD

1.The automatic drive disconnect must be in the DRIVE position (Figure 7).

2.Slowly release your left foot from the brake pedal.

3.Move the throttle control to the FAST position.

4.Slowly push the speed control pedal forward to the desired speed (Figure 6).

5.To increase forward speed, slowly move the speed control pedal forward. To reduce forward speed, slowly release the speed control pedal until the unit slows to the desired speed.

Speed Control

Pedal

Figure 6

HOW TO DRIVE IN REVERSE

1.Look to the rear.

2.Slowly push the speed control pedal to the REVERSE position.

HOW TO CHANGE DIRECTIONS

CAUTION: To change directions, do not use the left brake pedal. Use only the speed control pedal.

1.Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL position.

2.When the unit stops, slowly move the speed control pedal to the desired direction.

SPEED CONTROL PEDAL POSITIONS

The forward speed is controlled by the position of the speed control pedal. The following chart provides functions along with the pedal positions. Always operate the engine with the throttle control in the FAST position.

FUNCTION

PEDAL

THROTTLE

 

POSITION

 

 

 

 

Trimming

1/3

 

Snow Thrower

 

 

 

 

 

Bagging Grass

1/3 to 1/2

 

 

 

FAST

 

 

CHOKE

Normal Mowing

1/2 to 2/3

FAST

 

 

 

 

SLOW

Easy Mowing

1/2 to 3/4

THROTTLE

Snow Blade

 

 

 

 

Transport

FULL

 

 

 

 

Pull Behind

1/3 to 1/2

 

Attachments

 

 

 

 

 

HOW TO DISCONNECT THE TRANSMISSION

To push the unit, use the automatic drive disconnect to release the transmission. The automatic drive disconnect is under the seat.

1.The engine must be off.

2.Raise the seat. The automatic drive disconnect is under the seat.

3.Move and latch the automatic drive disconnect in the PUSH position (Figure 7). The transmission is now released and the unit can be pushed.

NOTE: In cold weather, the heavy viscosity oil in the transmission will make the unit difficult to push.

4.To engage the transmission, unlatch the automatic drive dis- connect. The transmission is now connected and ready to op- erate.

F-030727L

16

Automatic Drive Disconnect

PUSH POSITION

Seat

Automatic Drive Disconnect

DRIVE POSITION

Figure 7

Image 16
Contents Model Table of Contents Environmental Awareness OWNER’S InformationSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering Wheel100105417x47 25x3 17x146Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayHOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionTo 1/2 To 2/3HOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Change the Mulcher Plate How To Remove The Mulcher PlateMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingRemove the mower drive belt from the stack pulley Attach the extension spring to the blade control rod. SeeLift Lever Hole No Position No HOW to Adjust the Gauge Wheels5,6 HOW to Level the Mower Housing Install the mid-idler pulley HOW to Replace the Motion Drive BeltRemove the mid-idler pulley HOW to Replace the Primary Mower Drive Belt HOW to Replace the Secondary Mower Drive BeltAssemble the left pulley cover Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 030727L030727L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Electrical System Key Part Description030727L 030727L 030727L Index Model No Model No Bushel Capacity

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.