Murray 465600x8A manual HOW to Adjust the Blade Rotation Control

Page 24

MAINTENANCE

HOW TO ADJUST THE BLADE ROTATION CONTROL

WARNING: To prevent an injury, the blade rotation control must operate correctly.

In normal usage, the blade rotation control will not require an adjustment. However, if the cutting performance decreases or the quality of cut is poor, make the following changes.

1.When you mow, make sure the throttle control in in the FAST position.

2.Move the blade rotation control to the DISENGAGE position (Figure 16).

3.Stop the engine. Disconnect the wire from the spark plug.

Disengage

Position

Blade Rotation Control

Engage Position

Figure 16

4.Check the blade(s). Keep a sharp edge on the blade(s). A blade that is not sharp will cause the tips of the grass to become brown.

5.Disconnect the blade drive spring from the blade control rod. Move the blade drive spring to the middle hole (Figure 17). This will increase the tension on the mower drive belt.

DISENGAGE POSITION

Blade

 

Top Hole (New Belt)

 

 

Control Rod

 

Middle Hole

 

 

Bottom Hole

 

Blade Drive Spring

Figure 17

 

 

6.Attach the wire to the spark plug. Mow for a short distance and again check the quality of cut. If necessary, move the blade drive spring to the bottom hole.

7.Again check the quality of cut. If the quality of cut has not im- proved, replace the mower drive belt. See “How To Replace The Mower Drive Belt”. If replacing the belt does not correct the problem, take the unit to an authorized service center.

8.Move the blade rotation control to the DISENGAGE posi- tion. Stop the engine. Disconnect the wire from the spark plug. Check the operation of the blade brake. Rotate the pul- leys with your hand. Make sure the brake pads are pressed tightly against the pulleys (Figure 18).

WARNING: If the brake pads do not press tightly against the pulleys, take the unit to an authorized service center.

Blade Brake

(Pad Against Pulley)

Figure 18

9.Move the blade rotation control to the ENGAGE position. Check the pads for the blade brake. If the pads are excessively worn or damaged, replace the brake pad assemblies. Correct replacement parts and assistance are available from an autho- rized service center.

10.Attach the wire to the spark plug. Mow for a short distance and again check the operation of the blade rotation control.

11.When you move the blade rotation control to the DISENGAGE position, all movement will stop within five se- conds. If there is movement of the belt or the blades continue to rotate, engage and disengage the blade rotation control five times to remove any excess rubber from a new mower drive belt. If you need assistance, take the unit to an autho- rized service center.

12.If you replace the mower drive belt, move the blade drive spring to the top hole (Figure 17).

F-030727L

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering Wheel100105417x47 25x3 17x146Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayHOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionTo 1/2 To 2/3HOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsHOW to Start the Engine Before Starting the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Change the Mulcher Plate How To Remove The Mulcher PlateMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingRemove the mower drive belt from the stack pulley Attach the extension spring to the blade control rod. SeeHOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley HOW to Replace the Primary Mower Drive Belt HOW to Replace the Secondary Mower Drive BeltAssemble the left pulley cover Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 030727L030727L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Electrical System Key Part Description030727L 030727L 030727L Index Model No Model No Bushel Capacity

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents