Murray 465600x8A manual HOW to Operate with the Mower Housing, HOW to Operate the Unit on Hills

Page 18

OPERATION

HOW TO OPERATE WITH THE MOWER HOUSING

WARNING: The deflector is a safety device. Do not re- move the deflector. The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position. If the deflector is dam- aged, replace the deflector with an original equipment part from an authorized service center.

1.Start the engine.

2.Release the parking brake.

3.Move the lift lever to a height of cut position. In high or thick grass, cut the grass in the highest position first and then lower the mower housing to a lower position.

CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged.

4.Move the throttle control to the SLOW position.

5.Move the blade rotation control to the ENGAGE position.

6.Move the throttle control to the FAST position.

7.Slowly push the speed control pedal to the desired speed.

NOTE: When you mow in heavy grass or mow with a grass bagger, use a slow forward speed.

8.Make sure the level of cut set at the factory is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section.

WARNING: For better control of the unit, always select a safe speed.

HOW TO OPERATE THE UNIT ON HILLS

WARNING: Do not ride up or down slopes that are too steep to back straight up. Never ride the unit across a slope. See the “Slope Guide” in the back of this book for information on how to check slopes.

HOW TO OPERATE ON A HILL

1.Control the speed only with the speed control pedal. Do not use the brake pedal on a hill.

2.To help prevent an accident, slowly move the speed control pedal. Avoid sudden turns or changes in speed.

3.To reduce forward speed when going down a hill, slowly release the speed control pedal until the unit slows to the desired speed.

HOW TO STOP ON A HILL

1.Avoid stopping on a hill. If you must quickly stop in an emergen- cy, remove your right foot from the speed control pedal and quickly depress the left brake pedal.

2.Set the parking brake.

3.Before you dismount from the seat, move the throttle control to SLOW position, move the blade rotation control to the DISEN- GAGED position, turn off the engine and set the parking brake.

HOW TO START OPERATION ON A HILL

1.Start the engine

2.Move the blade rotation control to the ENGAGED position.

3.Move the throttle control to the FAST position.

4.Depress the brake pedal and release the parking brake. As you release the parking brake, push the speed control pedal to the desired speed.

WARNING: Slowly push the speed control pedal as you release the parking brake. The parking brake must be disengaged before the speed control pedal is able to engage the transmission.

F-030727L

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly Assembly100105417x47 HOW to Install the SeatHOW to Assemble the Steering Wheel 25x3 17x146HOW to Install the Battery Cables Maintenance Free BatteryHOW to Charge Maintenance Free Battery Remove the battery and battery trayIMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsTo 1/2 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 2/3HOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsHOW to Start the Engine Before Starting the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Change the Mulcher Plate How To Remove The Mulcher PlateHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterRemove the mower drive belt from the stack pulley HOW to Remove the Mower HousingHOW to Install the Mower Housing Attach the extension spring to the blade control rod. SeeHOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley Assemble the left pulley cover HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 030727L030727L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Electrical System Key Part Description030727L 030727L 030727L Index Model No Model No Bushel Capacity

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents