Murray 465600x8A manual HOW to Replace the Motion Drive Belt, Remove the mid-idler pulley

Page 31

MAINTENANCE

HOW TO REPLACE THE MOTION DRIVE BELT

REMOVAL

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the mid-idler pulley.

3.Disconnect the idler spring (Figure 35).

4.Remove the idler pulley and spacer (Figure 35).

5.Remove the V-idler pulley and spacer.

6.Remove the motion drive belt from the drive pulley (Figure 35).

7.To remove the motion drive belt from the stack pulley, pull the front end of the belt under the stack pulley and then back between the stack pulley and the steering plate (Figure 33).

8.Remove the access panel (Figure 34).

9.Remove the two screws that attach the steering shaft assembly (Figure 34). Raise the steering wheel and steering shaft assembly. Pull the motion drive belt under the steering shaft assembly.

10.Remove the motion drive belt. A correct replacement part or assistance is available from an Authorized Service Center in your area.

INSTALLATION

1.Slide the motion drive belt between the stack pulley and the belt guides (Figure 33). Install the motion drive belt on the top pulley of the stack pulley. Make sure the “V” side of the belt is against the pulley.

2.Push the motion drive belt through the opening between the steering plate and the engine plate.

3.Install the end of the motion drive belt around the drive pulley (Figure 35).

4.Put the motion drive belt around the V-idler pulley. Install the motion drive belt, V-idler pulley and spacer.

5.Put the belt around the idler pulley. Fasten the idler pulley and spacer with the hex nut. Make sure the flat side of the belt is against the idler pulley. Also, make sure the belt is not twisted.

6.Connect the idler spring (Figure 35).

7.Install the mid-idler pulley.

8.Check the routing of the motion drive belt (Figure 35). Make sure the motion drive belt is installed correctly on the idler pulleys and inside all belt guides.

9.Attach the steering shaft assembly to the steering plate with two screws (Figure 34).

10.Attach the access panel (Figure 34).

11.Before you use the unit, check the adjustment of the clutch. See the instructions “How To Check And Adjust The Clutch”.

12.Install the mower housing. See the instructions “How To Install The Mower Housing”.

FRONT

Stack Pulley

Steering

 

 

Plate

Motion

 

Belt Guides

 

 

Drive

 

 

Belt

 

Figure 33

Screw

 

 

Steering Shaft

 

 

Assembly

 

 

Motion Drive

 

 

Belt

Access Panel

Figure 34

 

 

 

 

 

Belt Guide

 

 

 

 

 

Motion Drive Belt

Belt Guide

 

 

 

 

 

 

 

 

Mid-Idler

Pulley

 

 

 

Idler Spring

 

 

 

Idler Pulley

Spacer

 

 

Stack Pulley

Spacer

 

 

 

 

 

 

 

 

 

V-Idler

Pulley

 

 

 

 

 

 

V-Idler

Pulley

 

 

 

 

Drive Pulley

 

 

 

 

 

Idler Spring

 

 

Figure 35

F-030727L

 

31

 

 

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model Table of Contents Environmental Awareness OWNER’S InformationSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly Assembly25x3 17x146 HOW to Install the SeatHOW to Assemble the Steering Wheel 100105417x47Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsHow To Remove The Mulcher Plate HOW to Change the Mulcher PlateGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingHOW to Install the Mower Housing Remove the mower drive belt from the stack pulleyLift Lever Hole No Position No HOW to Adjust the Gauge Wheels5,6 HOW to Level the Mower Housing Install the mid-idler pulley HOW to Replace the Motion Drive BeltRemove the mid-idler pulley Remove the primary mower drive belt from the stack pulley HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Assemble the left pulley coverFasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030727L MURRAY, INC. Lawn Mower Central Parts Distributors030727L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Key Part Description Electrical System030727L 030727L 030727L Index Model No Bushel Capacity Model No

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents