Murray 465600x8A HOW to Replace the Primary Mower Drive Belt, Assemble the left pulley cover

Page 32

MAINTENANCE

HOW TO REPLACE THE PRIMARY

MOWER DRIVE BELT

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the three screws from the left pulley cover. Remove the pulley cover.

3.To remove the primary mower drive belt from the left man- drel pulley, slide the primary mower drive belt between the left mandrel pulley and the belt guides.

4.Pull the belt retainer away from the idler pulley. Remove the primary mower drive belt from the idler pulley.

5.Move the brake pad assembly away from the stack pulley. Remove the primary mower drive belt from the stack pulley.

NOTE: Replace the primary mower drive belt with an original equipment belt. See an authorized service center in your area.

6.Install a new primary mower drive belt. Pull the brake pad as- sembly away from the stack pulley. Put the belt around the stack pulley. Make sure the primary mower drive belt is in- side of the belt guide.

7.Pull the belt retainer away from the idler pulley. Put the flat side of the primary mower drive belt around the idler pulley.

8.Make sure the “V” side of the primary mower drive belt is against the mandrel pulleys as shown.

9.Make sure the primary mower drive belt is inside all the belt guides.

10.Assemble the left pulley cover.

11.Install the mower housing. See the instructions on “How To In- stall The Mower Housing”.

12.Before you mow, check the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.

HOW TO REPLACE THE SECONDARY MOWER DRIVE BELT

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Remove the primary mower drive belt from the stack pulley.

3.Remove the two screws from the right pulley cover. Remove the right pulley cover.

4.Pull the idler pulley away from the secondary mower drive belt. Remove the belt from the idler pulley.

5.Remove the secondary mower drive belt from the right man- drel pulley.

6.Remove the secondary mower drive belt from the stack pulley.

NOTE: Replace the secondary mower drive belt with an original equipment belt. See an authorized service center in your area.

7.Install a new secondary mower drive belt. Put the belt around the bottom of the stack pulley. Make sure the secondary mower drive belt is inside the belt guide next to the stack pulley.

8.Put the secondary mower drive belt around the right drive pulley.

9.Pull the idler pulley toward the front. Install the flat side of the secondary mower drive belt against the idler pulley.

10.Make sure the “V” side of the secondary mower drive belt is around the right mandrel pulley.

11.Assemble the right pulley cover.

12.Put the primary mower drive belt around the stack pulley.

13.Install the mower housing. See the instructions on “How To In- stall The Mower Housing”.

14.Before you mow, check the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.

 

 

Left

 

Screw

Pulley Cover

Screw

 

 

 

Idler Pulley

Belt

 

 

Right Pulley Cover

 

Retainer

 

Stack Pulley

Left

 

 

Mandrel Pulley

Brake Pad

Belt Guide

 

Assembly

Belt Guide

 

 

Secondary

 

 

Mower Drive Belt

 

 

Right

 

 

Mandrel

 

 

Pulley

 

 

 

 

Brake Pad Assembly

 

 

Primary Mower Drive Belt

Idler Pulley

 

Figure 36

 

 

F-030727L

32

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering Wheel100105417x47 25x3 17x146Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayHOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionTo 1/2 To 2/3HOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsCarburetor HOW to Start the EngineBefore Starting the Engine Operating Tips Mowing and Bagging TipsHOW to Change the Mulcher Plate How To Remove The Mulcher PlateMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingRemove the mower drive belt from the stack pulley Attach the extension spring to the blade control rod. See5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley HOW to Replace the Primary Mower Drive Belt HOW to Replace the Secondary Mower Drive BeltAssemble the left pulley cover Remove the primary mower drive belt from the stack pulleyHOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 030727L030727L Repair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Electrical System Key Part Description030727L 030727L 030727L Index Model No Model No Bushel Capacity

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents