Murray 465600x8A Inspect Blade, HOW to Remove and Install the Blade, HOW to Sharpen the Blade

Page 23

MAINTENANCE

INSPECT BLADE

WARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.

If you keep the blade sharp and inspect the blade for damage, the blade will cut better and be more safe to operate. Frequently check the blade for excessive wear, cracks, or other damage. Frequently check the nut that holds the blade. Keep the nut tight. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. See if the blade is bent or damaged. Check the blade adapter for damage. Before you operate the unit, replace damaged parts with original equipment parts. See the authorized service center in your area. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment part.

HOW TO REMOVE AND INSTALL THE BLADE

1.Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.

2.Use a piece of wood to keep the blade from rotating.

3.Remove the nut that holds the blade (Figure 13).

Hi-Lift

Edge Up

Mandrel

Blade Adapter

Blade

Belleville Washer

 

Washer

Nut

Figure 13

 

4.

Check the blade and the blade adapter according to the in-

 

structions for “Inspect Blade”. Replace a badly worn or dam-

 

aged blade with an original equipment blade. See an

 

authorized service center in your area.

5.

Clean the top and bottom of the mower housing. Remove all the

9.Tighten the nut that holds the blade to a torque of 35 foot pounds (47,5 N-m).

10.Install the mower housing. See “How To Install The Mower Housing”.

Blade Adapter

 

 

Blade

 

Washer

Belleville Washer

Nut

 

(Outside rim must be

Figure 14

against the blade.)

HOW TO SHARPEN THE BLADE

WARNING: Vibration can be caused if the blade is not correctly balanced or if the blade is damaged. A blade that is damaged with cracks can break and cause an accident.

Keep a sharp edge on the blade. A blade that is not sharp will cause the tips of the grass to become brown.

1.Sharpen the blade two times a year or every 25 hours.

2.Remove the blade according to the instructions in “How To Re- move And Install The Blade”.

3.Clean the blade with a brush, soap and water. Check the blade. Look for cracks, nicks, or other damage. Replace a badly worn or damaged blade with an original equipment blade. See an authorized service center in your area.

4.Sharpen the blade with a file (Figure 15). Make sure you keep the original bevel angle.

5.Make sure the blade is balanced. Use a screwdriver and hold the blade parallel to the ground (Figure 15). A blade that is balanced will stay parallel to the ground. If the blade is not bal- anced, the heavy end will rotate toward the ground. Sharpen the heavy end until the blade is balanced.

6.A new blade will cut better than a badly worn blade. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment blade.

7.Assemble the blade according to the instructions “How To Re- move And Install The Blade”.

 

grass and debris.

6.

Mount the blade and blade adapter on the mandrel

 

(Figure 13).

7.

Mount the blade so that the hi-lift edges are up. If the blade

 

is upside down, the blade will not cut correctly and can cause

 

an accident.

8.

Fasten the blade with the original washers and nut. Make sure

 

the outside rim of the Belleville washer is against the blade

 

(Figure 14).

WARNING: Always keep the nut tight that holds the blade. A loose nut or blade can cause an accident.

F-030727L

23

Screwdriver

Blade is balanced

when parallel to the ground.

Ground

Blade

File

Figure 15

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly Assembly25x3 17x146 HOW to Install the SeatHOW to Assemble the Steering Wheel 100105417x47Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsHow To Remove The Mulcher Plate HOW to Change the Mulcher PlateGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateAttach the extension spring to the blade control rod. See HOW to Remove the Mower HousingHOW to Install the Mower Housing Remove the mower drive belt from the stack pulley5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley Remove the primary mower drive belt from the stack pulley HOW to Replace the Primary Mower Drive BeltHOW to Replace the Secondary Mower Drive Belt Assemble the left pulley coverFasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart 030727L MURRAY, INC. Lawn Mower Central Parts Distributors030727L Chassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601031 Engine Mount Assembly Repair Parts Repair Parts Electrical System Key Part Description Electrical System030727L 030727L 030727L Index Model No Bushel Capacity Model No

465600x8A specifications

The Murray 465600x8A is a remarkable innovation in the realm of industrial machinery, specifically designed to meet the demanding needs of various sectors. This versatile equipment stands out for its impressive performance and advanced technologies, making it a favorable choice for businesses striving for efficiency and reliability.

One of the most significant features of the Murray 465600x8A is its robust construction. Built with high-grade materials, this machine ensures durability and longevity, even in the most challenging environments. The rugged design allows it to withstand heavy usage, making it ideal for industrial applications where downtime is not an option.

Equipped with a powerful engine, the Murray 465600x8A delivers exceptional performance. Its engine is designed for high torque, providing the necessary power to tackle demanding tasks with ease. The machine operates smoothly under various conditions, ensuring that productivity is maintained without interruption.

The Murray 465600x8A also embraces cutting-edge technology, featuring an advanced control system that enhances user experience and operational efficiency. This system allows for precise adjustments and real-time monitoring, enabling operators to optimize performance and reduce waste. This technology not only elevates productivity but also contributes to greater energy efficiency, leading to cost savings over time.

In terms of safety features, the Murray 465600x8A is designed with user protection in mind. It comes with an array of safety mechanisms, including emergency stop functions and protective guards, ensuring that operators can work with peace of mind. The intuitive design of the controls also minimizes the learning curve for new users, promoting a safe working environment.

Another notable characteristic of the Murray 465600x8A is its flexibility. The machine can be easily integrated into various operational setups, allowing it to adapt to different workflows. This adaptability makes it a valuable asset for companies looking to enhance their operational capabilities.

Overall, the Murray 465600x8A is an exemplary model of industrial machinery that embodies strength, efficiency, and safety. Its advanced features and robust performance make it a top choice for industries such as construction, manufacturing, and logistics, where reliability and productivity are of utmost importance. As businesses continue to seek ways to improve operations, the Murray 465600x8A stands out as a trustworthy partner in achieving these objectives.
Top Page Image Contents