Craftsman 917.2720601 manual To Remove Tractor from Carton

Page 8

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS

REQUIRED FOR ASSEMBLY

 

Insert

A socket

wrench set will make assembly

_

_._ /11/2 Hex Nut

easier. Standard wrench sizes you need

 

 

are

listed below.

 

 

(1)

3/4"wrench

(1)

Pliers

(2)

7116"wrench

(1)

Utility knife

(1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating

__LargeFlat _asher

Steering _.__-_

_

Wheel-""-- L_@!_'_/

Steering

position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut, from top to bottom, along lines on all four comers of carton, and lay panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower

steering shaft. Align mounting holes in extension and lower shafts and

install 1/4 hex bolt and Iocknut.

Tighten securely.

IMPORTANT: Tighten bolt and nut securely to 10-12 ft. Ibs torque.

2.Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cress bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 1/2 hex nut and tighten securely.

7.Snap steering wheel insert into center of steering wheel.

8.Remove protective materials from

tractor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

CHECK BA'I-I'ERY

1.Lift seat pan to raised position, NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BAFFERY" in Maintenance section of this manual for charging instructions).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Icraftsmani Sears Craftsman Help Line 5 am 5 pro, Mon SatLimited Warranty on Craftsman Riding Equipment II. Slope Operation General OperationIV. Service Do notPage Repair Agreement Customer ResponsibilitiesFor Future Use 28 x 1-1/4To Remove Tractor from Carton Before Removing Tractor from Skid Attach Steering WheelRelease parking brake by depressing clutch/brake pedal Install SeatLabel Terminal Install Mulcher Plate Check Brake System To Convertto Bagging or DischargingCheck Tire Pressure Check Deck LevelnessAutomatic Models only Know Your Tractor PlungerFreewheel Control Disengagages transmission for pushingHOW to USE Your Tractor To Adjust Gauge Wheels To Operate on HillsGaug To Operate MowerTo Start Engine Before Starting the Engine Check Engine OIL LevelADD Gasoline Automatictransmissionwarmup Purge TransmissionMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsCh=,v-Bait Before Each USEBattery TractorBrake Operation TiresEngine AIR Filter Clean AIR ScreenEngine OIL Filter Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsTo Install Mower TractorTo Remove Mower PulleyTo Level Mower Housing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Belt InstallationTo Adjust Brake With Parking BrakeNut Jam Nut To Replace Motion Drive BeltTransaxle Motion Control Lever Neutral Adjustment To Adjust Steering Wheel ALIGN- MentTransmission REMOVAL/REPLACE- Ment Front Wheel TOE-IN/CAMBERTo Remove CABLES, Reverse Order Replacing BAI-FERYTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor Thr ttle Idle Speed AdjustingIAcceleration Test ScrewEngine OtherTractor Cause Correction Troubleshooting ChartProblem Troubleshooting Chart Problem Cause CorrectionProblem Cause Correction FastSlow OFFSchematic Tractor --MODEL NumberTRACTOR-- Modelnumber ElectricalTractor --MODEL Number Electrical KEY Part DescriptionTractor -- Model Number 917.2720601 Chassis and Enclosures Tractor --MODEL Number 917.2720601 Chassis and Enclosures KEY Part DescriptionTRACTOR-- Model Number Grounddrive Ground Drive Tractor -- Model Number 917.2720601 Steering Assembly Tractor - Model Number 917.2720601 Steering Assembly KEY Part NO. NO. DescriptionSpark Arrester Tractor -- Model Number EngineOptional Equipment Tractor -- Model Number Liftassembly KEY Part NO. no DescriptionSeat Assembly Tractor --MODEL Number Decals Wheels & TiresMowerdeck Mower Deck Mi= Tractor -- Model Number Hydro Gear Transaxle - Model Number 142883Cylinder HEAD, Valve and Breather Crankcasej 041 03-S KEY Part NO. no3NITIONIELECTRICAL Blower Housing and Baffles AIR Intake Not Illustrated Starting System Engine Controls OIL PAN I Lubrication J OIL PAN/LUBRICATION Starting System KEY Part DescriptionCrankshaftexhaust SScrew, thread forming M5x0.8xl SKit, solenoid repairPage Suggested Guide for Sighting Slopes for Safe Operation SU-HOGAR sa 888-784.-6427 6am -11 pm, 7 daysaweekM 5 pm., CST, Mort.- Sat Rn.-8 p m. EST, M- F, 4 p m S

917.2720601 specifications

The Craftsman 917.2720601 is a standout lawn tractor that combines robust functionality with user-friendly features, making it a go-to choice for many homeowners looking to maintain their yards efficiently. With its powerful performance and innovative technologies, this model is designed to enhance the mowing experience while ensuring durability and reliability.

One of the main features of the Craftsman 917.2720601 is its engine. Powered by a reliable 19 horsepower Briggs & Stratton engine, it provides ample power to efficiently cut through thick grass and tackle various landscaping tasks. The engine is equipped with an automatic choke system, ensuring easy starts in various weather conditions.

The cutting deck plays a crucial role in the effectiveness of any lawn tractor, and the 917.2720601 does not disappoint. It features a 42-inch cutting deck, which allows for a wide cutting path, reducing the time spent mowing large areas. The deck height can be easily adjusted with a simple lever, providing six different height positions. This feature allows users to achieve the perfect cut, whether they prefer a manicured look or a more natural appearance.

One of the standout technologies integrated into this lawn tractor is the Easy Access battery and fuel system. This design enhances user convenience by allowing quick access for maintenance checks and fuel refills. Additionally, with its hydrostatic transmission, the Craftsman 917.2720601 offers smooth and reliable speed control, making it easy for users to navigate different terrains without any hassle.

Comfort is also a priority with this model. The tractor features an adjustable high back seat, designed to provide optimum support during prolonged use. Large, durable wheels ensure stability and traction on uneven ground, enhancing the overall mowing experience.

Safety features are another important aspect of this tractor. It includes a safety switch that prevents operation when the seat is unoccupied, reducing the risk of accidents. The easy-to-use controls are intuitively designed, allowing even novice users to operate the tractor with confidence.

In conclusion, the Craftsman 917.2720601 is a well-rounded lawn tractor that offers a combination of power, versatility, and comfort. With its robust engine, efficient cutting deck, user-friendly features, and safety technologies, it's an ideal choice for anyone looking to achieve a beautifully maintained lawn with ease. Whether for small or large yards, this tractor is equipped to meet a variety of mowing needs.
Top Page Image Contents