Craftsman 917.273648 manual To Adjust Steering Wheel Alignment, To Remove Wheel for Repairs

Page 26

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align

grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant

also prevents tire dry rot and corrosion.

 

Washers

Retaining

Ring

Axle

 

Cove r --......_,

Square Key

i

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

A(_,WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT-

TERY" in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

 

 

02614

Weak or Dead

Fully Charged

Battery

 

Battery

REPLACING

BATTERY

_WARNING:

Do

not short battery

terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,

rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Criiftsmhn Limitedwarrantyon Craftsmanridingequipment General Operation II. Slope OperationIII. Children IV. ServiceDo not Page Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities For Future Use Unpack Carton HOW to SET UP Your Tractor Check BatteryAdjust Seat Check for Proper Position ALL Belts Reposition Right Rear Gauge WheelDischarging Check Brake SystemVchecklist @@@@ Tractor Stopping To Adjust Mower Cutting HeightTo SET Parking Brake EngineTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportADD Gasoline Towing Carts and Other Attach MentsBefore Starting the Engine Check Engine OIL Level Automatic Transmission Warm UP Purge TransmissionMulching Mowing Tips Mowing TipsMaintenance Schedule General RecommendationsOperator Presence System BatteryTractor Blade CareTransaxle Pump Fluid Engine LubricationEngine Cooling System Engine OIL FilterAIR Filter MufflerTo Remove Mower To Install MowerDisengaged FRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment with Bubble Level To Replace Mower Blade Drive Belt To Check and Adjust BrakeBoth Front Links Must be Equal Length To Replace Motion Drive Belt Lever Neutral AdjustmentReplacement Transaxle Motion ControlTo Remove Wheel for Repairs To Adjust Steering Wheel AlignmentReplacing Battery Interlocks and Relays To Adjust Throttle Control CableTo Replace Headlight Bulb To Replace FuseFinal Setting To Adjust CarburetorPreliminary Setting Acceleration TestCylinders Engine Fuel SystemEngine OIL OtherStart ProblemCause Correction Loss of power CauseProblemcause CorrectionSchematic DiodeElectrical Electrical KEY Part DescriptionTractor - Model Number 917,273648 Chassis and Enclosures Part Description Tractor - Model Number Ground Drive Tractor - Model Number 917,273648 Ground Drive KEY Part DescriptionTractor - Model Number 917,273648 Steering Assembly Tractor - Model Number 917.273648 Steering Assembly Engine Optional EquipmentTractor - Model Number Seat Assembly \25 13 \\\\Wheels Tires KEY PartTractor - Model Number 917,273648 Lift Assembly Part KEY Description144 ,.....4s Tractor - Model Number 917,273648 Mower DeckTractor Model Number STD206 KEY Part Description 783J Briggs ENGINE-MODEL Number 31P777, Type Number 0348-E1 105137 276 Dimensions Given in U.S. inches Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXOurHome

917.273648 specifications

The Craftsman 917.273648 is a powerful and versatile riding lawn mower designed for homeowners who seek efficiency in lawn maintenance. This riding mower is equipped with a robust 24-horsepower Kohler engine, ensuring it can tackle even the most challenging terrains with ease. Its reliable performance is matched with an easy-start feature, allowing you to fire up the engine without hassle.

One of the standout features of the Craftsman 917.273648 is its cutting deck, which measures 46 inches. This wide cutting deck allows for a more extensive mowing area, reducing the time spent on large lawns. The deck is engineered from high-quality steel, providing durability and resilience against wear and tear. Additionally, the deck height can be adjusted to six different positions ranging from 1.5 to 4 inches, giving users the flexibility to achieve their desired grass length.

The mower also incorporates advanced technologies such as a hydrostatic transmission, allowing for smooth and seamless speed adjustments while driving. This feature enhances the mowing experience, making it comfortable to navigate around obstacles without needing to shift gears manually. The tight turning radius of the Craftsman 917.273648 enables efficient maneuvering, making it easier to turn around flower beds or other landscaping features.

In terms of operator comfort, the Craftsman 917.273648 includes an ergonomic seat with ample padding, designed to minimize fatigue during extended mowing sessions. The controls are intuitively laid out, ensuring that users can operate the mower with minimal effort. Furthermore, the mower is equipped with an oversized lap bar, making it simple to control steering and braking.

Safety features are also a priority with this model. It comes with a safety switch that automatically shuts off the mower if the operator leaves the seat, preventing accidents. The rear engine placement enhances visibility while mowing, ensuring that users can safely navigate their landscapes.

Overall, the Craftsman 917.273648 combines power, comfort, and safety in a reliable riding mower. With its robust engine, versatile cutting deck, and user-friendly features, it stands out as a top choice for homeowners looking to maintain their lawns efficiently.
Top Page Image Contents