Craftsman 917.273648 To Adjust Gauge Wheels, To Operate Mower, To Operate on Hills, To Transport

Page 14

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted

when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Be sure tractor is on a flat level surface.

1.Lower mower and adjust mower to de-

sired cutting height(See "TO ADJUST MOWER CUTTING HEIGHT" in this

section of manual).

2.Remove retainer spring and clevis pin which secure each gauge wheel bar.

3.Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4.Replace retainer spring into clevis pin.

5.Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge wheels if you change the cutting height of the mower deck.

Retainer

Spring

Clevis

Pin

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut.

2.Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

_kCAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

Attachment Clutch Switch

Attachemnt

Pull Out To "Engage"

Lift Lever High

 

 

Position

"/"_

Low

 

Position

 

Shield

_

eflector

TO OPERATE ON HILLS

_WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual.

•Choose the slowest speed before start- ing up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi- tion and engage parking brake.

•Move motion control lever to neutral (N)

position.

IMPORTANT: The motion control lever does not return to neutral (N) position when the clutch/brake pedal is depressed.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT

When pushing or towing your tractor, be sure to disengage transmission by placing

freewheel control in freewheeling position. Freewheel control is located at the rear

drawbar of tractor.

1.Raise attachment lift to highest posi- tion with attachment lift control.

2.Pull freewheel control out and down into the slot and release so it is held in

the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To re-engage transmission, reverse above procedure.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Criiftsmhn Limitedwarrantyon Craftsmanridingequipment General Operation II. Slope OperationIII. Children IV. ServiceDo not Page Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities For Future Use Unpack Carton HOW to SET UP Your Tractor Check BatteryAdjust Seat Check for Proper Position ALL Belts Reposition Right Rear Gauge WheelDischarging Check Brake SystemVchecklist @@@@ Tractor Stopping To Adjust Mower Cutting HeightTo SET Parking Brake EngineTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportADD Gasoline Towing Carts and Other Attach MentsBefore Starting the Engine Check Engine OIL Level Automatic Transmission Warm UP Purge TransmissionMulching Mowing Tips Mowing TipsMaintenance Schedule General RecommendationsOperator Presence System BatteryTractor Blade CareTransaxle Pump Fluid Engine LubricationEngine Cooling System Engine OIL FilterAIR Filter MufflerTo Remove Mower To Install MowerDisengaged FRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment with Bubble Level To Replace Mower Blade Drive Belt To Check and Adjust BrakeBoth Front Links Must be Equal Length To Replace Motion Drive Belt Lever Neutral AdjustmentReplacement Transaxle Motion ControlTo Remove Wheel for Repairs To Adjust Steering Wheel AlignmentReplacing Battery Interlocks and Relays To Adjust Throttle Control CableTo Replace Headlight Bulb To Replace FuseFinal Setting To Adjust CarburetorPreliminary Setting Acceleration TestCylinders Engine Fuel SystemEngine OIL OtherStart ProblemCause Correction Loss of power CauseProblemcause CorrectionSchematic DiodeElectrical Electrical KEY Part DescriptionTractor - Model Number 917,273648 Chassis and Enclosures Part Description Tractor - Model Number Ground Drive Tractor - Model Number 917,273648 Ground Drive KEY Part DescriptionTractor - Model Number 917,273648 Steering Assembly Tractor - Model Number 917.273648 Steering Assembly Engine Optional EquipmentTractor - Model Number Seat Assembly \25 13 \\\\Wheels Tires KEY PartTractor - Model Number 917,273648 Lift Assembly Part KEY Description144 ,.....4s Tractor - Model Number 917,273648 Mower DeckTractor Model Number STD206 KEY Part Description 783J Briggs ENGINE-MODEL Number 31P777, Type Number 0348-E1 105137 276 Dimensions Given in U.S. inches Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXOurHome

917.273648 specifications

The Craftsman 917.273648 is a powerful and versatile riding lawn mower designed for homeowners who seek efficiency in lawn maintenance. This riding mower is equipped with a robust 24-horsepower Kohler engine, ensuring it can tackle even the most challenging terrains with ease. Its reliable performance is matched with an easy-start feature, allowing you to fire up the engine without hassle.

One of the standout features of the Craftsman 917.273648 is its cutting deck, which measures 46 inches. This wide cutting deck allows for a more extensive mowing area, reducing the time spent on large lawns. The deck is engineered from high-quality steel, providing durability and resilience against wear and tear. Additionally, the deck height can be adjusted to six different positions ranging from 1.5 to 4 inches, giving users the flexibility to achieve their desired grass length.

The mower also incorporates advanced technologies such as a hydrostatic transmission, allowing for smooth and seamless speed adjustments while driving. This feature enhances the mowing experience, making it comfortable to navigate around obstacles without needing to shift gears manually. The tight turning radius of the Craftsman 917.273648 enables efficient maneuvering, making it easier to turn around flower beds or other landscaping features.

In terms of operator comfort, the Craftsman 917.273648 includes an ergonomic seat with ample padding, designed to minimize fatigue during extended mowing sessions. The controls are intuitively laid out, ensuring that users can operate the mower with minimal effort. Furthermore, the mower is equipped with an oversized lap bar, making it simple to control steering and braking.

Safety features are also a priority with this model. It comes with a safety switch that automatically shuts off the mower if the operator leaves the seat, preventing accidents. The rear engine placement enhances visibility while mowing, ensuring that users can safely navigate their landscapes.

Overall, the Craftsman 917.273648 combines power, comfort, and safety in a reliable riding mower. With its robust engine, versatile cutting deck, and user-friendly features, it stands out as a top choice for homeowners looking to maintain their lawns efficiently.
Top Page Image Contents