Orion C05001, C08001 owner manual High Level Harnesses, Amplifier Settings

Page 6

HIGH LEVEL HARNESSES

Do not connect the high level input connections to power, signal, or chassis ground as damage to the head-unit outputs may result. The high-level inputs are designed to work with either grounded or BTL speaker level outputs (found on most head units).

HIGH LEVEL CONNECTIONS

WIRE COLOR

INPUT CONNECTION

 

 

Black

Ground

 

 

White/Black

- Left channel

 

 

White

+ Left channel

 

 

Gray/Black

- Right channel

 

 

Gray

+ Right channel

 

 

AMPLIFIER SETTINGS

Signal Input and Output Configurations

The input section of the amplifier consists of a phase switch that sets the output configuration, gain controls, and RCA inputs. The input section makes it easy to adapt this amplifier to most system configurations.

Input Gain

The Orion Cobalt CO5001 and CO8001 amplifiers have level adjustments to allow for easy inte- gration with any source unit. The input sensitivity can be adjusted from 200mV to 5V. Refer to Testing the System and Adjusting the Sound of the System sections of this guide for detailed instructions on setting the gain.

Phase Switches

0° - leaves output unaffected. The output signal is in phase with the input signal.

180° - inverts the output. The channel is 180° output of phase. This configuration is useful for inverting the phase of subwoofers to improve staging in a vehicle. This is also used when bridging two amplifiers into one speaker.

Auxiliary Output Configurations

The auxiliary outputs on Orion Cobalt amplifiers offer easy, unlimited system expansion. Routing signal from a source unit, pre-amplifier, or equalizer is a matter of connecting RCAs to the RCA Inputs and the RCA outputs to your next Orion Cobalt amplifier in the signal chain. The signal passes through a buffer stage so that several amplifiers can be daisy chained without signal loss or overloading of the source unit. This maximizes the signal output and minimizes the potential for system noise.

Internal Crossover

The crossover section of the Orion Cobalt CO5001 and CO8001 amplifiers is continuously variable and extremely flexible.

When using Orion Cobalt loudspeakers, minor deviations from the recommended frequency ranges can provide superior results depending on your speaker locations and your vehicle acoustics. Setting crossover frequencies higher than recommended will not cause damage and may provide superior sonic results depending on your system's performance goals. Refer to your

© 2008 directed electronics—all rights reserved

5

Image 6
Contents Amplifier Table of Contents Introduction WHAT’S in the BOXPractice Safe Sound Tools of the Trade END Panel LayoutsInput Plate CEA Specifications Output PlateAmplifier Settings High Level HarnessesSpeaker Wiring Diagram CO5001/CO8001 Amplifier WiringPower Connections for the Orion Cobalt CO5001 and CO8001 Low-Pass CrossoverChoosing Mounting Locations Amplifier InstallationBridging Passenger CompartmentGeneral Precautions and Installation Tips Step By Step InstallationTrunk Compartment SET UP and Troubleshooting Testing the SystemAdjusting the Sound of the System Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Action To Take Specifications Amplifier Section CO5001 CO8001Crossover Section Directed electronics-all rights reserved Agencement DES Panneaux Dextrémité Panneau dentrée figurePanneau de sortie figure Faisceaux À Haut Niveau Configurations dentrée et sortie du signalSpécifications DE Lace Réglages DE LamplificateurCâblage DE Lamplificateur Câblage des haut-parleurs CO5001/CO8001 Installation DE LamplificateurChoix de lemplacement du montage Branchement en pontPrécautions générales et conseils dinstallation Installation étape par étapeCoffre Réglage ET Dépannage Essai du systèmeRéglage sonore du système Conseils de dépannage Symptôme Cause probable FaireDirected electronics-all rights reserved Spécifications Section amplificateur CO5001 CO8001Section répartiteur Disposiciones DEL Panel DE Extremo Placa de entrada figuraPlaca de salida figura Especificaciones DE LA CEA Configuraciones DEL AmplificadorConfiguraciones de salida y entrada de señal Arneses DE Cableado DE Alto NivelCableado DEL Amplificador Conexión en puente Diagrama de cableado de altavoces del CO5001/CO8001Instalación DEL Amplificador Selección de ubicaciones de montajeCompartimiento de pasajeros MaleteroPrecauciones generales y sugerencias de instalación Configuración Y Detección Y Reparación DE Averías Instalación paso a pasoPrueba del sistema Ajuste de sonido del sistema Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarDirected electronics-all rights reserved Especificaciones Sección de amplificador CO5001 CO8001Sección de crossover Layout DER Endplatten Anschlussplatte abbildungAusgangsplatte abbildung HOCHPEGEL-LEITUNGSSYSTEME Signaleingangs- und -ausgangskonfigurationenCEA-DATEN VerstärkereinstellungenVerstärkeranschluss Brückenmodus VerstärkerinstallationLautsprecher-Anschlussdiagramm CO5001/CO8001 Wahl der EinbaustelleAllgemeine Vorsichts- und Installationshinweise FahrgastraumKofferraum Einrichtung UND Problembehebung Schrittweise InstallationSystemtest Systemsound einstellen Problemlösungen Symptom Mögliche Ursache LösungDirected electronics-all rights reserved Daten Verstärkerbereich CO5001 CO8001Crossover-Bereich Layout DEI Pannelli Terminali Pannello d’ingresso figuraPannello di uscita figura Cavi DI Livello Alto Configurazione dei segnali d’ingresso e di uscitaSpecifiche CEA Impostazioni DELL’AMPLIFICATORECablaggio DELL’AMPLIFICATORE Installazione DELL’AMPLIFICATORE Scelta del punto di installazioneCablaggio a ponte Precauzioni generali e suggerimenti per l’installazione AbitacoloBagagliaio Messa a Punto E Soluzione DEI Problemi Procedura di installazioneProva dell’impianto Regolazione dell’audio dell’impianto Soluzione dei problemi Sintomo Causa probabile Intervento necessarioDirected electronics-all rights reserved Dati Tecnici Sezione amplificatore CO5001 CO8001Sezione crossover Layouts DOS Painéis Painel de entrada figuraPainel de saída figura Ligações DE Alto Nível Configurações de entrada e saída dos sinaisEspecificações DA CEA Ajustes do AmplificadorConexão DOS Cabos do Amplificador Ligação em ponte Instalação do AmplificadorEsquema de conexão dos alto-falantes ao CO5001/CO8001 Escolha de locais de instalaçãoCabine de passageiros Porta-malasPrecauções gerais e sugestões de instalação Instalação E Resolução DE Problemas Instalação passo a passoComo testar o sistema Como ajustar o som do sistema Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaDirected electronics-all rights reserved Especificações Seção do amplificador CO5001 CO8001Seção do crossover Warranty

C08001, C05001 specifications

The Orion C05001 and C08001 represent a remarkable leap in technology and innovation, designed to cater to the evolving demands of modern users in various sectors, from industrial applications to advanced consumer electronics. These models stand out not just for their robust performance but also for their cutting-edge features.

Starting with the Orion C05001, this device showcases a sleek and compact design, making it an ideal choice for those who prioritize portability without compromising functionality. It is equipped with a powerful processor that ensures seamless multitasking and efficient handling of resource-intensive applications. The C05001 also boasts enhanced connectivity options, including advanced wireless capabilities, which allow users to stay connected even in remote areas.

In terms of display, the C05001 offers a high-resolution screen that provides clear, vibrant visuals, making it suitable for both professional presentations and entertainment purposes. The device’s battery life is another strong point, featuring long-lasting performance that enables users to work or play without the constant worry of recharging.

On the other hand, the Orion C08001 takes performance up a notch with its larger display and enhanced processing power. This model is ideal for users who require a more immersive experience, whether for gaming, graphic design, or data analysis. The C08001 supports advanced graphics, making it suitable for high-demand applications that require detailed visuals and fast frame rates.

Both models leverage state-of-the-art technologies, including artificial intelligence and machine learning capabilities. These features enable smarter performance optimization, energy efficiency, and intuitive user interfaces that adapt to user preferences and habits.

Another key characteristic of the Orion C05001 and C08001 is their durable construction, designed to withstand tough conditions. This resilience makes them perfect for industrial environments where reliability is paramount.

Moreover, security features in both models ensure that users' data remains protected, incorporating encryption and biometric authentication, which are increasingly essential in today’s digital landscape.

In summary, the Orion C05001 and C08001 are not just devices; they are engineered solutions that combine high performance, cutting-edge technology, and robust features, making them suitable for a wide range of applications, from everyday tasks to complex industrial challenges. Their innovative designs promise to enhance productivity and user experience, setting new standards in their respective categories.