Orion C05001 Amplifier Installation, Bridging, Choosing Mounting Locations, Passenger Compartment

Page 8

Bridging

For bridging into a single speaker load, the Orion Cobalt CO5001 and CO8001 have the ability to be bridged with another amplifier of the same model. To do this you must set the PHASE switch on the (slave) amp, move the phase switch from 0 to 180, exactly opposite of the master amp. Refer to the Phase Switch section of this guide.

Be sure to set all adjustment on both amplifiers exactly the same except for the phase switch. The phase switch on the master amplifier should be 0 and the slave amplifier should be 180. For the speaker connections, connect the positive (+) speaker lead from the speaker to the posi- tive (+) speaker terminal of the master amplifier. On the negative (-) speaker connection, take the negative (-) speaker terminal of the master amplifier and connect it directly to the nega- tive (-) speaker terminal of the (slave) amplifier. The remaining positive (+) speaker terminal of the (slave) amplifier must be connected to the negative (-) speaker lead from the speaker. The impedance of the speaker must not be less than 4 ohms

NOTE: For best results, connect both negative speaker terminals on the master amp to both negative terminals on the slave amp using at least 12 AWG cable.

2 ea. amplifiers bridged to 1 ea. 4Ω or 8Ω speaker

MASTER

SLAVE

PHASE 0º

PHASE 180º

Figure 4

-

-

+

+

-

-

+

+

Figura 4 Abbildung 4

4Ω or 8Ω

AMPLIFIER INSTALLATION

Choosing Mounting Locations

The location of your amplifier will depend on several important issues. Due to the low profile size of the Orion Cobalt amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance. Always mount the amplifier in a place that protects the amplifier from the elements. In addition, mount the amplifier on a stable, flat surface.

NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown.

WARNING! Do not mount any amplifier in the engine compartment. Amplifiers are not designed to endure the harsh environment of the exterior elements.

Passenger Compartment

If you are going to mount the amplifier in the passenger compartment, make sure you have adequate room for ventilation. The amplifiers have been designed to make under-seat mount- ing possible. When mounting your amplifier under a seat or similar area, keep a minimum of 1" of clearance around the amplifier for adequate cooling.

© 2008 directed electronics—all rights reserved

7

Image 8
Contents Amplifier Table of Contents Practice Safe Sound IntroductionWHAT’S in the BOX Input Plate Tools of the TradeEND Panel Layouts CEA Specifications Output PlateAmplifier Settings High Level HarnessesAmplifier Wiring Power Connections for the Orion Cobalt CO5001 and CO8001Speaker Wiring Diagram CO5001/CO8001 Low-Pass CrossoverAmplifier Installation BridgingChoosing Mounting Locations Passenger CompartmentTrunk Compartment General Precautions and Installation TipsStep By Step Installation SET UP and Troubleshooting Testing the SystemAdjusting the Sound of the System Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Action To Take Crossover Section SpecificationsAmplifier Section CO5001 CO8001 Directed electronics-all rights reserved Panneau de sortie figure Agencement DES Panneaux DextrémitéPanneau dentrée figure Configurations dentrée et sortie du signal Spécifications DE LaceFaisceaux À Haut Niveau Réglages DE LamplificateurCâblage DE Lamplificateur Installation DE Lamplificateur Choix de lemplacement du montageCâblage des haut-parleurs CO5001/CO8001 Branchement en pontCoffre Précautions générales et conseils dinstallationInstallation étape par étape Réglage ET Dépannage Essai du systèmeRéglage sonore du système Conseils de dépannage Symptôme Cause probable FaireDirected electronics-all rights reserved Section répartiteur SpécificationsSection amplificateur CO5001 CO8001 Placa de salida figura Disposiciones DEL Panel DE ExtremoPlaca de entrada figura Configuraciones DEL Amplificador Configuraciones de salida y entrada de señalEspecificaciones DE LA CEA Arneses DE Cableado DE Alto NivelCableado DEL Amplificador Diagrama de cableado de altavoces del CO5001/CO8001 Instalación DEL AmplificadorConexión en puente Selección de ubicaciones de montajePrecauciones generales y sugerencias de instalación Compartimiento de pasajerosMaletero Prueba del sistema Configuración Y Detección Y Reparación DE AveríasInstalación paso a paso Ajuste de sonido del sistema Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarDirected electronics-all rights reserved Sección de crossover EspecificacionesSección de amplificador CO5001 CO8001 Ausgangsplatte abbildung Layout DER EndplattenAnschlussplatte abbildung Signaleingangs- und -ausgangskonfigurationen CEA-DATENHOCHPEGEL-LEITUNGSSYSTEME VerstärkereinstellungenVerstärkeranschluss Verstärkerinstallation Lautsprecher-Anschlussdiagramm CO5001/CO8001Brückenmodus Wahl der EinbaustelleKofferraum Allgemeine Vorsichts- und InstallationshinweiseFahrgastraum Systemtest Einrichtung UND ProblembehebungSchrittweise Installation Systemsound einstellen Problemlösungen Symptom Mögliche Ursache LösungDirected electronics-all rights reserved Crossover-Bereich DatenVerstärkerbereich CO5001 CO8001 Pannello di uscita figura Layout DEI Pannelli TerminaliPannello d’ingresso figura Configurazione dei segnali d’ingresso e di uscita Specifiche CEACavi DI Livello Alto Impostazioni DELL’AMPLIFICATORECablaggio DELL’AMPLIFICATORE Cablaggio a ponte Installazione DELL’AMPLIFICATOREScelta del punto di installazione Bagagliaio Precauzioni generali e suggerimenti per l’installazioneAbitacolo Prova dell’impianto Messa a Punto E Soluzione DEI ProblemiProcedura di installazione Regolazione dell’audio dell’impianto Soluzione dei problemi Sintomo Causa probabile Intervento necessarioDirected electronics-all rights reserved Sezione crossover Dati TecniciSezione amplificatore CO5001 CO8001 Painel de saída figura Layouts DOS PainéisPainel de entrada figura Configurações de entrada e saída dos sinais Especificações DA CEALigações DE Alto Nível Ajustes do AmplificadorConexão DOS Cabos do Amplificador Instalação do Amplificador Esquema de conexão dos alto-falantes ao CO5001/CO8001Ligação em ponte Escolha de locais de instalaçãoPrecauções gerais e sugestões de instalação Cabine de passageirosPorta-malas Como testar o sistema Instalação E Resolução DE ProblemasInstalação passo a passo Como ajustar o som do sistema Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaDirected electronics-all rights reserved Seção do crossover EspecificaçõesSeção do amplificador CO5001 CO8001 Warranty

C08001, C05001 specifications

The Orion C05001 and C08001 represent a remarkable leap in technology and innovation, designed to cater to the evolving demands of modern users in various sectors, from industrial applications to advanced consumer electronics. These models stand out not just for their robust performance but also for their cutting-edge features.

Starting with the Orion C05001, this device showcases a sleek and compact design, making it an ideal choice for those who prioritize portability without compromising functionality. It is equipped with a powerful processor that ensures seamless multitasking and efficient handling of resource-intensive applications. The C05001 also boasts enhanced connectivity options, including advanced wireless capabilities, which allow users to stay connected even in remote areas.

In terms of display, the C05001 offers a high-resolution screen that provides clear, vibrant visuals, making it suitable for both professional presentations and entertainment purposes. The device’s battery life is another strong point, featuring long-lasting performance that enables users to work or play without the constant worry of recharging.

On the other hand, the Orion C08001 takes performance up a notch with its larger display and enhanced processing power. This model is ideal for users who require a more immersive experience, whether for gaming, graphic design, or data analysis. The C08001 supports advanced graphics, making it suitable for high-demand applications that require detailed visuals and fast frame rates.

Both models leverage state-of-the-art technologies, including artificial intelligence and machine learning capabilities. These features enable smarter performance optimization, energy efficiency, and intuitive user interfaces that adapt to user preferences and habits.

Another key characteristic of the Orion C05001 and C08001 is their durable construction, designed to withstand tough conditions. This resilience makes them perfect for industrial environments where reliability is paramount.

Moreover, security features in both models ensure that users' data remains protected, incorporating encryption and biometric authentication, which are increasingly essential in today’s digital landscape.

In summary, the Orion C05001 and C08001 are not just devices; they are engineered solutions that combine high performance, cutting-edge technology, and robust features, making them suitable for a wide range of applications, from everyday tasks to complex industrial challenges. Their innovative designs promise to enhance productivity and user experience, setting new standards in their respective categories.