Orion C08001, C05001 owner manual Adjusting the Sound of the System

Page 11

System section of this manual.

Adjusting the Sound of the System

Once you have checked the system's operation, adjust the sound of the system. Adjusting the sound of the system is accomplished by setting the level controls and adjusting the internal crossovers.

Step 1 Turn the signal source volume control all the way down. Set any tone controls to their flat or defeated positions. This includes the loudness control.

Step 2 Turn the level controls of the amplifier to their minimum positions.

Step 3 Choose music with high dynamic content that you like, with which you are famil- iar, and will be used most often in the system.

Step 4 Turn the source unit's volume control up to its highest undistorted output level. If you lack test equipment, this point occurs between 3/4 to full volume depending on the quality of your source unit. Listen for any audible distortion. If any distor- tion is audible, reduce the volume of the source unit until you have an undistorted output. Leave the volume control at this position during your system tuning.

Step 5 While listening to your chosen dynamic music, turn up the level control corre- sponding to the midrange output until you hear slight distortion and turn the level control back slightly for an undistorted output. Depending on your system, the midrange and tweeter output may be on the same output channels.

Step 6 Turn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output. Depending on your system the midrange and tweeter output may be on the same output channels.

Step 7 Fine-tune the output level between midrange and tweeters. Refer to the Internal

Crossover Configuration section of this manual for detailed instructions.

Step 8 Repeat Steps 5-7 for the rear speakers. If you do not have rear speakers continue to Step 10.

Step 9 Set levels between the front and rear midrange and tweeters for optimum front/ rear balance.

Step 10 Turn up the level control corresponding to the woofer output until you hear slight distortion and turn back the level control slightly for an undistorted output.

Step 11 Fine-tune the output level between satellite speakers and the woofers. Refer to the Internal Crossover Configuration section of this manual for detailed instruc- tions. If using an RGC-2, adjust the level to the bass output of the woofer to match the sonic requirements of the system.

Step 12 Enjoy your awesome Orion Cobalt sound system.

10

© 2008 directed electronics—all rights reserved

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Amplifier Table of Contents Practice Safe Sound IntroductionWHAT’S in the BOX Input Plate Tools of the TradeEND Panel Layouts Output Plate CEA SpecificationsHigh Level Harnesses Amplifier SettingsLow-Pass Crossover Amplifier WiringPower Connections for the Orion Cobalt CO5001 and CO8001 Speaker Wiring Diagram CO5001/CO8001Passenger Compartment Amplifier InstallationBridging Choosing Mounting LocationsTrunk Compartment General Precautions and Installation TipsStep By Step Installation Testing the System SET UP and TroubleshootingAdjusting the Sound of the System Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Action To Take Crossover Section SpecificationsAmplifier Section CO5001 CO8001 Directed electronics-all rights reserved Panneau de sortie figure Agencement DES Panneaux DextrémitéPanneau dentrée figure Réglages DE Lamplificateur Configurations dentrée et sortie du signalSpécifications DE Lace Faisceaux À Haut NiveauCâblage DE Lamplificateur Branchement en pont Installation DE LamplificateurChoix de lemplacement du montage Câblage des haut-parleurs CO5001/CO8001Coffre Précautions générales et conseils dinstallationInstallation étape par étape Essai du système Réglage ET DépannageRéglage sonore du système Symptôme Cause probable Faire Conseils de dépannageDirected electronics-all rights reserved Section répartiteur SpécificationsSection amplificateur CO5001 CO8001 Placa de salida figura Disposiciones DEL Panel DE ExtremoPlaca de entrada figura Arneses DE Cableado DE Alto Nivel Configuraciones DEL AmplificadorConfiguraciones de salida y entrada de señal Especificaciones DE LA CEACableado DEL Amplificador Selección de ubicaciones de montaje Diagrama de cableado de altavoces del CO5001/CO8001Instalación DEL Amplificador Conexión en puentePrecauciones generales y sugerencias de instalación Compartimiento de pasajerosMaletero Prueba del sistema Configuración Y Detección Y Reparación DE AveríasInstalación paso a paso Ajuste de sonido del sistema Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasDirected electronics-all rights reserved Sección de crossover EspecificacionesSección de amplificador CO5001 CO8001 Ausgangsplatte abbildung Layout DER EndplattenAnschlussplatte abbildung Verstärkereinstellungen Signaleingangs- und -ausgangskonfigurationenCEA-DATEN HOCHPEGEL-LEITUNGSSYSTEMEVerstärkeranschluss Wahl der Einbaustelle VerstärkerinstallationLautsprecher-Anschlussdiagramm CO5001/CO8001 BrückenmodusKofferraum Allgemeine Vorsichts- und InstallationshinweiseFahrgastraum Systemtest Einrichtung UND ProblembehebungSchrittweise Installation Systemsound einstellen Symptom Mögliche Ursache Lösung ProblemlösungenDirected electronics-all rights reserved Crossover-Bereich DatenVerstärkerbereich CO5001 CO8001 Pannello di uscita figura Layout DEI Pannelli TerminaliPannello d’ingresso figura Impostazioni DELL’AMPLIFICATORE Configurazione dei segnali d’ingresso e di uscitaSpecifiche CEA Cavi DI Livello AltoCablaggio DELL’AMPLIFICATORE Cablaggio a ponte Installazione DELL’AMPLIFICATOREScelta del punto di installazione Bagagliaio Precauzioni generali e suggerimenti per l’installazioneAbitacolo Prova dell’impianto Messa a Punto E Soluzione DEI ProblemiProcedura di installazione Regolazione dell’audio dell’impianto Sintomo Causa probabile Intervento necessario Soluzione dei problemiDirected electronics-all rights reserved Sezione crossover Dati TecniciSezione amplificatore CO5001 CO8001 Painel de saída figura Layouts DOS PainéisPainel de entrada figura Ajustes do Amplificador Configurações de entrada e saída dos sinaisEspecificações DA CEA Ligações DE Alto NívelConexão DOS Cabos do Amplificador Escolha de locais de instalação Instalação do AmplificadorEsquema de conexão dos alto-falantes ao CO5001/CO8001 Ligação em pontePrecauções gerais e sugestões de instalação Cabine de passageirosPorta-malas Como testar o sistema Instalação E Resolução DE ProblemasInstalação passo a passo Como ajustar o som do sistema Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasDirected electronics-all rights reserved Seção do crossover EspecificaçõesSeção do amplificador CO5001 CO8001 Warranty

C08001, C05001 specifications

The Orion C05001 and C08001 represent a remarkable leap in technology and innovation, designed to cater to the evolving demands of modern users in various sectors, from industrial applications to advanced consumer electronics. These models stand out not just for their robust performance but also for their cutting-edge features.

Starting with the Orion C05001, this device showcases a sleek and compact design, making it an ideal choice for those who prioritize portability without compromising functionality. It is equipped with a powerful processor that ensures seamless multitasking and efficient handling of resource-intensive applications. The C05001 also boasts enhanced connectivity options, including advanced wireless capabilities, which allow users to stay connected even in remote areas.

In terms of display, the C05001 offers a high-resolution screen that provides clear, vibrant visuals, making it suitable for both professional presentations and entertainment purposes. The device’s battery life is another strong point, featuring long-lasting performance that enables users to work or play without the constant worry of recharging.

On the other hand, the Orion C08001 takes performance up a notch with its larger display and enhanced processing power. This model is ideal for users who require a more immersive experience, whether for gaming, graphic design, or data analysis. The C08001 supports advanced graphics, making it suitable for high-demand applications that require detailed visuals and fast frame rates.

Both models leverage state-of-the-art technologies, including artificial intelligence and machine learning capabilities. These features enable smarter performance optimization, energy efficiency, and intuitive user interfaces that adapt to user preferences and habits.

Another key characteristic of the Orion C05001 and C08001 is their durable construction, designed to withstand tough conditions. This resilience makes them perfect for industrial environments where reliability is paramount.

Moreover, security features in both models ensure that users' data remains protected, incorporating encryption and biometric authentication, which are increasingly essential in today’s digital landscape.

In summary, the Orion C05001 and C08001 are not just devices; they are engineered solutions that combine high performance, cutting-edge technology, and robust features, making them suitable for a wide range of applications, from everyday tasks to complex industrial challenges. Their innovative designs promise to enhance productivity and user experience, setting new standards in their respective categories.
Top Page Image Contents