McCulloch M11577HRB, 96041012400 instruction manual Recherche des pannes . Búsqueda de averías

Page 91

7. Recherche des pannes. 7. Búsqueda de averías.

Le moteur ne démarre pas

1.Manque de carburant dans le réservoir.

2.Bougie d'allumage défectueuse.

3.Le câblage de la bougie d'allumage défectueux.

4.Il y a des impuretés dans le carburateur ou dans le circuit du carburant.

Le démarreur n'entraîne pas le moteur

1.La batterie est déchargée.

2.Mauvais contact entre les cosses des câbles de batterie et les bornes de la batterie.

3.Le levier de commande d'embrayage/débrayage n'est pas en bonne position.

4.Le fusible principal est hors d'usage.

5.Le contacteur de démarrage est endommagé.

6.Le contacteur de sécurité sur la pédale d'embrayage/ frein est défectueux ou endommagé.

7.La pédale d'embrayage/frein n'est pas suffisamment enfoncée.

Le moteur ne tourne pas régulièrement

1.Un rapport de vitesse trop élevé est enclenché.

2.La bougie est défectueuse.

3.Le carburateur est mal réglé.

4.Le filtre à air est colmaté.

5.La mise à l'air libre du réservoir est bouchée.

6.Le réglage de l'allumage est incorrect.

7.Il y a des impuretés dans le circuit de carburant.

Le moteur manque de puissance

1.Le filtre à air est colmaté.

2.La bougie d'allumage est défectueuse

3.Il y a des impuretés dans le circuit de carburant.

4.Le carburateur est mal réglé.

Le moteur chauffe

1.Le moteur est en surcharge.

2.La prise d'air ou les ailettes de refroidissement sont colmatées.

3.La turbine de refroidissement est endommagée.

4.Le niveau d'huile est trop bas ou il n'y a pas d'huile dans le moteur.

5.Le réglage de l'allumage est incorrect.

6.La bougie d'allumage est défectueuse.

La batterie ne charge pas

1.Le fusible est hors d'usage.

2.Une ou plusieurs cellules sont endommagées.

3.Mauvais contact entre les bornes de la batterie et les cosses des câbles de batterie.

L'éclairage ne fonctionne pas

1.Les ampoules sont grillées.

2.L'interrupteur de commande est défectueux.

3.Il y a un court circuit dans le faisceau de raccorde- ment.

Le tracteur vibre

1.Les lames de coupe sont mal fixées ou mal position- nées.

2.Le moteur est mal fixé.

3.Undéséquilibreestapparueàlasuitedel'endommagement d'une ou de plusieurs lames de coupe ou à la suite d'un mauvais affûtage.

Coupe irrégulière

1.Mauvais affûtage des lames de coupe.

2.Le carter de coupe n'est pas à l'horizontale.

3.L'herbe est haute et humide.

4.L'herbe est accumulée sous le carter de coupe.

5.La pression de gonflage des pneumatiques n'est pas identique du côté droit et du côté gauche.

6.Le rapport de vitesse enclenché est trop élevé.

7.La courroie d'entraînement du carter de coupe patine. 91

El motor no arranca

1.No hay combustible en el depósito.

2.La bujía es errónea.

3.La conexión de la bujía está defectuosa.

4.Hay suciedad en el carburador o en el tubo de combus- tible.

El motor de arranque no hace girar al motor

1.Batería descargada.

2.Mal contacto entre cable y borne de batería.

3.La palanca de acoplamiento/desacoplamiento en mala posición.

4.Fusible principal estropeado.

5.Cerradura de encendido estropeada.

6.Contacto de seguridad para pedal de embrague/freno estropeado.

7.Pedal de embrague/freno no apretado.

El motor funciona irregularmente

1.Acoplada una marcha demasiado alta.

2.La bujía está estropeada.

3.El carburador está mal ajustado.

4.El filtro de aire está obturado.

5.El orificio de ventilación del depósito de combustible está obturado.

6.La puesta a punto del encendido es errónea.

7.Hay suciedad en el tubo de combustible.

Falta potencia en el motor

1.Filtro de aire obturado.

2.Bujía estropeada.

3.Suciedad en el carburador o tubo de combustible.

4.Carburador mal ajustada.

El motor se calienta

1.El motor funciona sobrecargado.

2.Toma de aire o aletas de refrigeración obturadas.

3.Ventilador dañado.

4.Poco o ningún aceite en el motor.

5.El avance de encendido está mal ajustado.

6.La bujía es errónea.

La batería no se carga

1.Fusible estropeado.

2.Uno o varios vasos estropeados.

3.Mal contacto entre los bornes de la batería y los cables.

No funciona el alumbrado

1.Bombillas fundidas.

2.Interruptor estropeado.

3.Cortocircuito en el cable.

La máquina vibra

1.Las cuchillas están sueltas.

2.El motor está suelto.

3.Hay desequilibrio en una o ambas cuchillas por estar. dañadas o por defecto de equilibrado después del afi- lado.

Corte irregular

1.Cuchillas embotadas.

2.Unidad de corte mal ajustada.

3.Hierba larga o húmeda.

4.Acumulación de hierba debajo de la cubierta.

5.Presión de inflado desigual en los neumáticos derechos e izquirdos.

6.Hay acoplada una marcha demasiado alta.

7.Las poleas propulsoras resbalan.

Image 91
Contents M11577HRB Page III. Operation Safety RulesTraining II. PreparationIV. Maintenance and Storage III. Betrieb SicherheitsvorschriftenSchulung II. VorbereitungIV. Wartung UND Lagerung III. Utilisation Règles de SécuritéPrécautions D’UTILISATION II. PréparationIV. Entretien ET Entreposage III. Operación Reglas De SeguridadInstrucción II. PreparaciónIV. Mantenimiento Y Almacenamiento III. Funzionamento Norme AntinfortunisticheAddestramento ALL’USO II. PreparazioneIV. Manutenzione E Periodi DI INATTIVITA’ Maai alleen bij daglicht of goed kunstlicht VeiligheidsregelsII. Voorbereiding III. Bediening11,5/8,6 IV. Onderhoud EN Opslag190 Reverse Directive for Safety Hilfe Aufsuchen Züglich MIT WASExplosive Gase SER Ausspülen Sofort ÄrztlicheVolante DE Dirección Volant DE DirectionSteering Wheel LenkradEinstellen DES Sitzes Install SeatAdjust Seat Sitz MontierenAjustar EL Asiento Installazione DEL SedileInstallatie VAN DE Stoel Instalación DEL AsientoMise EN Place DE LA Batterie Install Battery Einbau DER BatterieAccu Installeren Installazione Della BatteriaInstalación DE LA Batería To prevent corrosion Prevent sparks from accidental groundingRemove terminal caps and discard. Connect the red Cable to + and then the black earth cable to -. ScrewBulloni a testa tonda Bulloni di spallamento 4 x 20 x Carriage Bolts Shoulder BoltsAnsatzschrauben Tornillos de cabeza redonda Pernos de topeHandle insert To Assemble BaggerTurn assembly right-side up To Install Bagger Component to Tractor To Install Bagger Full LEVER/PADDLEMontage DER Grasfangbox DER Schaufel Installation DES Beutelvollhebels UNDDen Grasfänger umdrehen Installation DER Aufhängung DER Grasfangbox DES Traktors Placez le bac 3 à l’envers, alignez les orifices du châssis Pour Assembler LE CollecteurFaites glisser les segments de boucle de tissu, situés aux Glisser lePour Assembler Composants DU Collecteur Pour Installer LE Levier DE Vidage DU BAC Avec LA PalettePara Montar EL Contenedor Paleta Para Instalar EL Brazo Completo CONGire el lado derecho hacia arriba Para Montar LOS Componentes DEL Contenedor AL Tractor PER Montare IL Cesto DI Raccolta Allineare i fori nel deflettore erba 29 con le protuberanze Estremità del sacco sul tubo del telaio per il sacco in altoPER Montare I Componenti DEL Cesto DI Raccolta PER Montare UNA LEVA/PALA Riempimento SaccoDE Grascontainer Monteren VOL-HENDEL/SCHOEP HET Installeren VAN DE OpvangbakZet de assemblage weer met de goede kant naar boven Voorkant Tractor Anordnung der Bedienungseinrichtungen Positioning of controlsComandi Emplacement des commandesUbicación de los mandos De plaats van de bedieningsorganen Comando gas/choke Commande des gaz et starterGas-und kaltstarthebel Mandos del acelerador y del estranguladorPedal del embrague/Freno Clutch/Brake PedalKupplungs-/Bremspedal Pédale de frein/D’embrayageAcoplamiento/desacoplamiento de la transmisión Levier de commande de la transmission hydrostatiqueMotion control lever Ein- und Ausschalten des AntriebesAcoplamiento y desacoplamiento del equipo de corte Commande dembrayage et de débrayage du carter de coupeConnection/disconnection of the cutting unit Ein und Ausschalten des MähaggregatsElevación/descenso rápidos del equipo de corte Quick lifting/lowering of the cutting unitSchnelles Heben und Senken des Mähaggregats Relevage et abaissement du carter de coupeZündschloß Ignition LockWarnung Freno de estacionamiento Parking brakeFeststellbremse Frein de stationnementPlein de carburant Filling upReposición de combustible TankenNivel de aceite Oil levelÖlstand Niveau d’huileDriving . Betrieb . Conduite . Conducción Guida . Rijden Hinweis Remarque HinweisNota Sistema de Funcionamiento Atrás ROS Reverse Operation System ROSRückwärtsgangsystem ROS Sécurité Marche Arrière ROSRatschläge zum Rasenmähen Sistema Per Operazioni In Retromarcia ROSSysteem Voor Achteruit ROS Cutting tipsMaaitips Conseils pour la tonteConsejos para el corte Consigli per il taglio dell’erbaBELANGRIJK! Loud Starten Voor Hydro IMPORTANT! Cold Starting for HydroIMPORTANTE! Empieso EN Frío Para HIDROS- Tático ATTENZIONE! Avviamento a Freddo PER TrasmissionSu tractor esta ahora dispuesto para la operación normal Purgar LA TransmisiónSpurgo Della Trasmissione Transmissie OntluchtenWaarschuwing WarnungAdvertencia PericoloApagar el motor Switching off the engineAbschalten des Motors Extinction du moteurAdvertencia Cubierta del motor Engine hoodMotorhaube Capot moteurMantenimiento MaintenanceWartung EntretienPara Cambiar EL Aceite To Change OILÖlwechsel Durchführen Pour Changer L’HUILEClean battery and terminals Check muffler Fill in dates as you complete regular service EveryCheck brake operation Clean air screen Clean engine cooling finsFiltre à air Sans filtre à huileVérification des freins Nettoyage de la grille daération Pré-filtreControllo pneumatici 50 oreControllo freni Pulizia schermo aria Pulizia raffreddamento motoreFahrer-Anwesenheitssystem und Rückwärts- gangsystem ROS Operator Presence System and Reverse Opera- tion System ROSControllo DEL Sistema PER Operazioni in RE- Tromarcia ROS Control Sistema Presencia OperadorControl Sistema DE Funcionamiento Atrás ROS Controllo DEL Sistema DI Presenza OperatoreMesserbalken BladesLames Lame CuchillasMessen Controlar El Freno To Check BrakeÜberprüfen Der Bremse Pour Vérifier Le FreinPour Démonter La Faucheuse PL QTo Remove Mower Entfernen Des MähersPL QD Pour remplacer la courroie de transmission To Replace Mower Drive BeltAustauschen des Antriebsriemens des Mähers Sustituir la correa de transmisión cortacéspedDe aandrijfriem van de maaiunit vervangen Sostituzione della cinghia di trasmissione del rasaerbaTo Level Mower FRONT-TO-BACK AdjustmentVisual SIDE-TO-SIDE Adjustment Precision SIDE-TO-SIDE AdjustmentGleich sind Ausnivellieren des MähersVisuelle Justierung AN Beiden Seiten Genaue justierung an beiden seitenRéglage D’AVANT EN Arrière Pour mettre la tondeuse à niveauRéglage Visuel Bilatéral Réglage Bilatéral DE PrécisionAjuste DE LA Parte Delantera a LA Trasera Nivelar el cortacéspedAjuste Visual DE Lado a Lado Ajuste DE Precisión DE Lado a LadoRegolazione DAVANTI-DIETRO Livellamento del rasaerbaRegolazione Visiva LATO-LATO Regolazione DI Precisione LATO-LATOAfstelling BOOR-EN Achterzijde De maaiunit nivellerenBeide Kanten OP HET OOG Uitlijnen PRECISIE-AFSTELLING BAN Beide Kanten BAN DE MaaiunitCambio de correa propulsora Replacement of drive beltRemplacement de la courroie dentraînement Auswechsein des TreibriemensWASCHANLAGEN-ÖFFNUNG DER Abdeckung Deck Washout PortPort DE Lavage DU Châssis Boca DE Lavado DE LA PlataformaDekreinigingspoort Apertura DI Lavaggio DEL PiattoTroubleshooting . Störungssuche Recherche des pannes . Búsqueda de averías Ricerca guasti . Het localiseren van fouten Servicio ServiceStorage . Aufbewahrung . Remisage . Conservación Entretien et réparationsServizio Rismessaggio . StallenPage 532 42 32-40 Rev 04.07.09 AP

M11577HRB, 96041012400 specifications

The McCulloch M11577HRB, model number 96041012400, is a robust and versatile lawn mower designed to deliver excellent performance for maintaining your garden. Known for its user-friendly features and cutting-edge technology, this mower stands out in the crowded market of lawn care equipment.

One of the key features of the McCulloch M11577HRB is its powerful 77cc engine, which ensures that it has the capacity to tackle various types of grass and terrain with ease. The engine technology provides reliable starts and consistent power delivery, making it an ideal choice for both residential and larger landscaping tasks.

Another significant characteristic of this mower is its cutting deck, which measures 51 centimeters. This wider deck allows for increased cutting efficiency, enabling users to cover more ground quickly while achieving a clean cut. The mower also comes with a cutting height adjustment feature, allowing operators to choose from different height settings, ranging from 25mm to 75mm. This flexibility enables users to customize their mowing experience according to the specific conditions of their lawns.

The McCulloch M11577HRB is designed with user comfort in mind. It features ergonomically designed handles that provide a comfortable grip, reducing fatigue during extended use. Additionally, the mower's lightweight yet durable construction makes it easy to maneuver around obstacles in the yard, ensuring that hard-to-reach areas are not neglected.

Integrated technologies in the McCulloch M11577HRB include a self-propelling system, which takes the strain off the operator by providing motorized assistance. This feature is particularly beneficial on slopes or uneven terrain, making mowing less physically demanding. The mower also incorporates a collection bag for clippings, which can be easily removed and emptied, promoting a clean and tidy mowing experience.

In summary, the McCulloch M11577HRB, 96041012400 model, combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners and landscapers alike. Its dependable engine, adjustable cutting height, and user-oriented design set it apart as a reliable tool for maintaining beautiful, healthy lawns. Whether you have a small garden or a larger yard, the McCulloch M11577HRB is equipped to handle the task with superior performance and ease.