Sears 917.275223 Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 22

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stoppingdistance at high speed in highestgear, then brake must be ad- justed. (See =TO ADJUST BRAKE" in the

Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See =PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fiat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and intedock systems are working propedy. If your tractor does not function as descdbed, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachment clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment dutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

IMPORTANT: To ensure proper assembly, canter hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt tighten belt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated.

Mandrel

Assembly

Trailing/

BladeBolt _.._

(Spaclal)__._Star

TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual

damage to mower end engine.

•The blade can be sharpened with a file or on a gdnding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel belt, pin, or a cone balancar. (When using a cone bal- ancer, follow the instructionssupplied

with balancar.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthraaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontalposition. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Boltor Pin

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

518"

Blade

1.Raise mower to highest position to allow access to blades.

2.Remove blade bolt.

3.Install new or resharpened blade with

trailing edge up towards deck as shown.

BATTERY Center Hole

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with

an automotive charger will extend its life.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Garden Tractor Limited 90 DAY Warranty on Battery Storage General OperationMow only in daylight or good artificial light I1. Slope OperationIV. Service Machine. Tall grass can hide obstaclesCancer and birth defects or other repro- ductive harm Speedmph Reverse Gasoline 3.5 GallonsAndtype Regular Repair AgreementRetainer Shoulder Bolt Steedng Sleeve SteedngWheellnse17132 x 1-3/16 x 12 Gauge Washers X 3/4 x 14 GaVideo Cassee Keys Slope Sheet Before Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyTo Removetractor from Carton Unpack Carton Teenng Steering Wheel Adapter Sleeve Tabs ExtensionInstall Seat Howto SET Upyourtractor Check BatteryBolt Assemble Gaugewheelsto Mower Deck Slide mower under tractor withCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Charged, Minimum 1 hour at 6 amps DampedENG,NEONENO,NEOFF.LRESSUREL,OHTSOND.P T Knowyourtractor Attachment Clutch SwitchLift Stopping To Adjust Mower Cutting HeightHowto Useyourtractor To SET Parking Brake Ground DriveDeflector Shield To Adjust Gauge WheelsTo Operate Mower To Operate on HillsBefore Starting the Engine Check Engine OIL Level To TransportTowing Carts and Other ATTACH- Ments ADD GasolineAutomatictransmission Warm UP Tion of clippings and more uniform cutting General Recommendations Lubrication ChartBefore Each USE Tires TractorBrake Operation Operator Presence SystemTransaxle Cooling To Clean Battery and TerminalsBelts Transaxle Pump FluidTo Service PRE-CLEANER Clean AIR ScreenClean AIR Intakeicooling Areas To Service CartridgeSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing Ractor To Remove MowerMower Drive Belt Installation FRONT-TO-BACK AdjustmentTo Replace Mower Drive Belt Mower Drive Belt Removal Electric Clutch To Replace Mower Blade Drive BeltTransaxle Motion Control Lever Neutral Adjustment To Adjust Attachment ClutchBelt Installation To Replace Motion Drive BeltTo Adjust TOE-IN To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN Adjustment BatteryTo Replace Fuse To Adjust Attachment Lift SpringTo Remove Hood and Grill Assembly To Replace Headlight BulbTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingAdjusting screw in or out until correct idle is attained Recheck idle speed. Readjust if necessaryEngine OIL 1RACTOREngine Fuel System CyundersTroubleshooting Chart ProblemWom. bent or loose blade Mower deck not level CauseCutting too much grass/too fast Throttle in Choke position CorrectionWet grass Mower deck not level Troubleshooting Chart Problem Cause CorrectionFaulty alternator Freewheel control in disengaged position OFFTRACTOR- Model Number Schematic Electrical TRACTORMODELNUMBER917-.275223 TRACTORMODELNUMBER917-.275223 Electrical TRACTOR- MODELNUMBER917.275223 Chassisandenclosures TRACTORMODELNUMBER917-.275223 Chassisandenclosures TRACTOR- MODELNUMBER917.275223 Grounddrive KEY Part NO. NO.DESCRIPTION TRACTOR- Model Number Steering KEY pART TRACTORMODELNUMBER917-.275223 Engine TRACTOR- Model Number Seatassembly TRACTORMODELNUMBER917-.275223 Decals TRACTOR- MODELNUMBER917.275223 LiFTASSEMBLY Ili TRACTOR- Model NU Mber Mowerdeck TRACTOR- MODELNUMBER917.275223 TRANSAXLE-MODELNUMBER311.3500 Screw Cylinder Head Valvi & Breather EADNALVE/BREATHER KEY IiI 24-164-06-S ECONTROLSp KEY Part NO. NO.DESCRIPTION Crankshaft Exhaust J Fuel System Not Illustrated Page Suggested Guide for Sighting Slopes for Safe Operation Part 0o..-7278

917.275223 specifications

The Sears 917.275223 is a robust lawn tractor that has earned a reputation among homeowners for its reliable performance and durability. Designed primarily for residential use, this lawn tractor features a user-friendly design that caters to both seasoned gardeners and those new to lawn care.

One of the standout characteristics of the Sears 917.275223 is its powerful engine, typically a Briggs & Stratton engine that delivers the necessary torque to tackle tough mowing conditions. This engine is known for its reliability and ease of starting, ensuring that homeowners can quickly get to work without frustration. Paired with a smooth-cutting deck, the tractor can efficiently handle various grass types and terrains with ease.

The cutting deck, often sized at 42 inches, provides a wide swath, allowing users to cover substantial ground in less time. Equipped with adjustable cutting heights, the Sears 917.275223 ensures a customizable mowing experience, which is beneficial for maintaining a healthy lawn. The ease of adjustment means users can switch between different grass and lawn types without hassle.

In terms of technology, the Sears 917.275223 often features a hydrostatic transmission. This technology allows for seamless speed adjustments without the need for manual gear changes, which is particularly advantageous when navigating uneven terrain or around landscaping features. The ease of steering is complemented by comfortable controls, putting everything within easy reach for the operator.

Another notable feature of this tractor is its ergonomic design. The seat is designed for comfort during longer mowing sessions, while the overall layout promotes ease of use. The placement of the foot pedals and steering wheel ensures that operators can maneuver and control the vehicle effortlessly.

The Sears 917.275223 is also designed with durability in mind. Constructed with high-quality materials, it can withstand the rigors of frequent lawn care tasks. Additionally, maintenance is simplified for the user, with easily accessible components for oil changes, belt adjustments, and other routine tasks.

In summary, the Sears 917.275223 lawn tractor combines a powerful engine, user-friendly technology, adjustable cutting options, and durable construction, making it a favorite among homeowners looking to maintain their lawns efficiently. With its thoughtful design and reliable performance, it stands as an excellent choice for both novice and experienced users alike.
Top Page Image Contents