Sears 917.275223 FRONT-TO-BACK Adjustment, To Replace Mower Drive Belt Mower Drive Belt Removal

Page 26

 

 

BOTH FRONT LINKS MUST BE EQUAL

 

 

IN LENGTH

SuspensionA_

 

 

_i,i_

Adjustment

 

_-""_

Nut

 

FRONT-TO-BACK ADJUSTMENT

 

IMPORTANT: Deck must be level side-to-

Nut "C"

side. If the following front-to-back adjustment is necessary, be sure to adjust

beth front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap

blade with heavy cloth.

Check adjustment on right side of tractor. Positionany blade so the tip is pointing straightforNard. Measure distance "13"at front and rear tip of blade

Before making any necessary adjust- ments, check that both front linksare equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of blade, loosen nut "C"

on both front links an equal number of turns.

NOTE: Each full turn of nut "C" will

change dim. "B" by approximately 3/16".

When distance "B" is 1/8" to 1/2" lower at front than rear, tighten nut "D" against trunnion on both front links.

To raise front of blade, loosen nut "D" from trunnion on both front links. Tighten nut =C"on both front links an equal number of turns.

When distance "B" is 1/8" to 1/2" lower

at front than rear, tighten nut "D" against trunnion on beth front links.

Recheck side-to-side adjustment.

Trunnion

Assembly

TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL

1.Park tractor on a level surface. Engage parking brake.

2.Lower mower to its lowest position.

3.Disengage belt tension rod from lock bracket.

1=CAUTION; R6d is spring loaded. Have a firm gdp on rod an release slowly.

4.Remove screws from R.H. mandrel cover and remove cover.

5.Remove any dirt or grass clippings which may have accumulated around

mandrels and entire upper deck surface.

6.Disconnect R.H. suspension arm from rear deck bracket by removing retainer spring.

7.Carefully roll belt over the top of R.H. mandrel pulley.

8.Remove belt from electric clutch pulley.

9.Remove belt from idler pulleys. 10.Check pdmary idler arm and two

idlers to see that they rotate freely.

11.Be sure spring is securely hooked to primary idler arm and spdng arm.

MOWER DRIVE BELT INSTALLATION

12.Install belt in both idlers.

13.Install new belt onto electric clutch pulley.

14.Carefully roll belt into upper groove of R.H. mandrel pulley.

15.Carefully check belt routing making sure belt is in the grooves correctly.

16.Reconnect R.H. suspension arm to rear deck bracket with retainer spdng.

17.Reassemble R.H. mandrel cover.

18.Engage belt tension red by pushing"

26

rod into locking bracket.

Image 26
Contents Garden Tractor Limited 90 DAY Warranty on Battery Storage General OperationMow only in daylight or good artificial light I1. Slope OperationIV. Service Machine. Tall grass can hide obstaclesCancer and birth defects or other repro- ductive harm Speedmph Reverse Gasoline 3.5 GallonsAndtype Regular Repair AgreementRetainer Shoulder Bolt Steedng Sleeve SteedngWheellnse17132 x 1-3/16 x 12 Gauge Washers X 3/4 x 14 GaVideo Cassee Keys Slope Sheet Before Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyTo Removetractor from Carton Unpack Carton Teenng Steering Wheel Adapter Sleeve Tabs ExtensionBolt Howto SET Upyourtractor Check BatteryInstall Seat Assemble Gaugewheelsto Mower Deck Slide mower under tractor withCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Charged, Minimum 1 hour at 6 amps DampedENG,NEONENO,NEOFF.LRESSUREL,OHTSOND.P T Lift Attachment Clutch SwitchKnowyourtractor Stopping To Adjust Mower Cutting HeightHowto Useyourtractor To SET Parking Brake Ground DriveDeflector Shield To Adjust Gauge WheelsTo Operate Mower To Operate on HillsBefore Starting the Engine Check Engine OIL Level To TransportTowing Carts and Other ATTACH- Ments ADD GasolineAutomatictransmission Warm UP Tion of clippings and more uniform cutting Before Each USE Lubrication ChartGeneral Recommendations Tires TractorBrake Operation Operator Presence SystemTransaxle Cooling To Clean Battery and TerminalsBelts Transaxle Pump FluidTo Service PRE-CLEANER Clean AIR ScreenClean AIR Intakeicooling Areas To Service CartridgeSIDE-TO-SIDE Adjustment To Install MowerTo Level Mower Housing Ractor To Remove MowerTo Replace Mower Drive Belt Mower Drive Belt Removal FRONT-TO-BACK AdjustmentMower Drive Belt Installation Electric Clutch To Replace Mower Blade Drive BeltTransaxle Motion Control Lever Neutral Adjustment To Adjust Attachment ClutchBelt Installation To Replace Motion Drive BeltTo Adjust TOE-IN To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN Adjustment BatteryTo Replace Fuse To Adjust Attachment Lift SpringTo Remove Hood and Grill Assembly To Replace Headlight BulbTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingAdjusting screw in or out until correct idle is attained Recheck idle speed. Readjust if necessaryEngine OIL 1RACTOREngine Fuel System CyundersTroubleshooting Chart ProblemWom. bent or loose blade Mower deck not level CauseCutting too much grass/too fast Throttle in Choke position CorrectionWet grass Mower deck not level Troubleshooting Chart Problem Cause CorrectionFaulty alternator Freewheel control in disengaged position OFFTRACTOR- Model Number Schematic Electrical TRACTORMODELNUMBER917-.275223 TRACTORMODELNUMBER917-.275223 Electrical TRACTOR- MODELNUMBER917.275223 Chassisandenclosures TRACTORMODELNUMBER917-.275223 Chassisandenclosures TRACTOR- MODELNUMBER917.275223 Grounddrive KEY Part NO. NO.DESCRIPTION TRACTOR- Model Number Steering KEY pART TRACTORMODELNUMBER917-.275223 Engine TRACTOR- Model Number Seatassembly TRACTORMODELNUMBER917-.275223 Decals TRACTOR- MODELNUMBER917.275223 LiFTASSEMBLY Ili TRACTOR- Model NU Mber Mowerdeck TRACTOR- MODELNUMBER917.275223 TRANSAXLE-MODELNUMBER311.3500 Screw Cylinder Head Valvi & Breather EADNALVE/BREATHER KEY IiI 24-164-06-S ECONTROLSp KEY Part NO. NO.DESCRIPTION Crankshaft Exhaust J Fuel System Not Illustrated Page Suggested Guide for Sighting Slopes for Safe Operation Part 0o..-7278

917.275223 specifications

The Sears 917.275223 is a robust lawn tractor that has earned a reputation among homeowners for its reliable performance and durability. Designed primarily for residential use, this lawn tractor features a user-friendly design that caters to both seasoned gardeners and those new to lawn care.

One of the standout characteristics of the Sears 917.275223 is its powerful engine, typically a Briggs & Stratton engine that delivers the necessary torque to tackle tough mowing conditions. This engine is known for its reliability and ease of starting, ensuring that homeowners can quickly get to work without frustration. Paired with a smooth-cutting deck, the tractor can efficiently handle various grass types and terrains with ease.

The cutting deck, often sized at 42 inches, provides a wide swath, allowing users to cover substantial ground in less time. Equipped with adjustable cutting heights, the Sears 917.275223 ensures a customizable mowing experience, which is beneficial for maintaining a healthy lawn. The ease of adjustment means users can switch between different grass and lawn types without hassle.

In terms of technology, the Sears 917.275223 often features a hydrostatic transmission. This technology allows for seamless speed adjustments without the need for manual gear changes, which is particularly advantageous when navigating uneven terrain or around landscaping features. The ease of steering is complemented by comfortable controls, putting everything within easy reach for the operator.

Another notable feature of this tractor is its ergonomic design. The seat is designed for comfort during longer mowing sessions, while the overall layout promotes ease of use. The placement of the foot pedals and steering wheel ensures that operators can maneuver and control the vehicle effortlessly.

The Sears 917.275223 is also designed with durability in mind. Constructed with high-quality materials, it can withstand the rigors of frequent lawn care tasks. Additionally, maintenance is simplified for the user, with easily accessible components for oil changes, belt adjustments, and other routine tasks.

In summary, the Sears 917.275223 lawn tractor combines a powerful engine, user-friendly technology, adjustable cutting options, and durable construction, making it a favorite among homeowners looking to maintain their lawns efficiently. With its thoughtful design and reliable performance, it stands as an excellent choice for both novice and experienced users alike.