Sears 917.257462 manual To Start Engine with a Weak Battery See Fig, To Remove Hood See FIG

Page 21

i

i

•

i

i

SERVICE AND ADJUSTMENTS

ii

TO REMOVE WHEEL FOR REPAIRS (See Fig. 29)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

WASHERS

RETAINING

RING

POSITIVE TERMINAL

NEGATIVE TERMINAL

CABLES

:HARGED

BA'I'rERY

POSITIVE TERMINAL

NEGATIVE TERMINAL

AXLE COVE R

_SQUAREKEY

 

 

(REAR WHEEL ONLY)

 

FIG. 29

FIG. 30

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The

fuse holder is located next to the battery box, accessible from left rear wheel area.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 30)

CAUTION: Lead-acid batteries gener- ate explosive gases. Keep sparks, flame and smoking materials away from bat-

teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. If "jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: YOUR UNIT IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE

(+)terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGA- TIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from left side of chassis and fully charged battery.

•RED cable last from both batteries.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running or prevent it from starting.

•Check wiring. See the electrical wiring diagram in the Repair Parts section of this manual.

TO REMOVE HOOD (See FIG. 31)

•With hood closed, remove hood spring from hole in grill strap.

•Remove left side and right side pivot.

•, Lift hood off unit.

•To reassemble hood, reverse above procedure.

HOOD

SPRING

 

\

i

•

 

PIVOT

RIGHT SIDE PIVOT SCREW

BRACKET

FIG. 31

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HP Electric Start 36 Mower Speed Lawn Rider SearsSafe Operation Practices for Ride-On Mowers Safety is InvolvedII. Slope Operation III. ChildrenFull 90 DAY Warranty on Battery Product SpecificationsMaintenance Agreement Customer ResponsibilitiesEngine MaintenancePerformance Sparkplug Muffler AIR Filter Stabilizer Blades BeltsTable of Contents Contents of Hardware Pack To Remove Unit from Carton Tools Required for AssemblyBefore Rolling Unit OFF Skid Unpack CartonHOW to SET UP Your Tractor AssemblyAll assembly instructions have been completed ChecklistKnow Your Lawn Rider OperationTo Move Forward and Backward To USE Throttle Control See FigSee Figs To SET Parking Brake See FigBefore Starting the Engine To Adjust Mower Cutting HeightTo Operate Mower See Figs To TransportImportant When Operating in Temperatures Mowing TipsADD Gasoline Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Care Lawn RiderBlade Removal See Fig Brake OperationEngine To Clean Battery and TerminalsAIR Filter See Fig Transaxle CoolingAIR Screen See Fig CleaningMuffler Spark PlugsMower Upstop Adjustment See Fig To Install Mower See FigLawn Rider To Remove Mower See FigService and Adjustments To Level Mower Housing See FigViewed from Front of Tractor To Adjust Steering Wheel Alignment To Adjust Brake See FigKeeper To Replace Motion Drive Belt See FigTo Remove Hood See FIG To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Replace FuseTo Adjust Throttle Control Cable To Adjust Carburetor See FigPreliminary Setting EngineOther BatteryTractor Fuel SystemProblem Cause Correction Troubleshooting PointsCause Correction ProblemSchematic Decals Wheels TiresKEY Part Description NO. no USAElectrical Electrical KEY Part DescriptionStandard Hardware - Purchase Locally Hood UNCStandard Hardware - Purchase Locally Fender / Chassis 129965 Case, BatteryFrame 19132012 WasherLocknut, Hex, Larg, Flange Seat1011 DashStandard Hardware Purchase Locally Steering Wheel KEY Part NO. no DescriptionLower, Steering Sector Gear / Axle Support Link, DragBolt, Hex Cap, Spindle Front Axle25/32 x 1-5/8 x 16 Gauge Standard Hardware Purchase LocallyKEY Brake / Rear Mower Lift Assembly122504X Hardware Shown LargerStandard Hardware Purchase Engine / ThrottleKeeper, Ground Drive Belt, Idler Ground DriveArm, Ground Drive Clutch Idler, Flat2530 TransaxlePulley Clip, Fuel Line Mower Lift Lever106932X STD560907Mower Deck Mower Deck 2631 2732 FOOTE/DANA Transaxle Model NumberFOOTE/DANA TRANSAXLE- Model Number 265 Briggs & Stratton Engine Model Number 283707, Type Number3O7 219 422224 138 445 66S42.1 801 310399265 Bearing, Cylinder Requires Special 224061 49045093805 391086635 66538 Mounting224546 Sighting Guide Only Ride UP and Down HILL, not Across Hill Sight and Hold this Level with SKY Line or TreeMAX HOW to Order Repair Parts Model Number 917,25746219.91

917.257462 specifications

The Sears 917.257462 is a well-known lawn tractor that has earned a reputation for its reliable performance and robust build. Designed for homeowners with medium to large yards, this model combines functionality and ease of use, making it an excellent choice for both novice and experienced gardeners.

One of the standout features of the Sears 917.257462 is its powerful engine. Equipped with a reliable, air-cooled, four-stroke engine, it offers ample horsepower to handle various mowing tasks. The engine's efficient design ensures that it provides consistent power while maintaining fuel economy, allowing owners to tackle extensive lawn areas without frequent refueling.

The cutting system of the Sears 917.257462 is designed for efficiency and versatility. It boasts a durable, reinforced mowing deck that allows for multiple cutting heights, accommodating different grass types and lawn conditions. This adaptability makes it easy to achieve a clean, even cut, regardless of the lawn's terrain. Additionally, the tractor features a bagging system that aids in collecting grass clippings for a tidy finish.

Ergonomics play a crucial role in the design of the Sears 917.257462. The operator's seat is adjustable, providing comfort and promoting good posture during extended use. The steering system is responsive, facilitating easy maneuverability around obstacles in the yard. The controls are intuitively placed, making it simple for users to operate the tractor while focusing on the task at hand.

Another key characteristic of this tractor is its durability. Constructed with high-quality materials, the Sears 917.257462 is built to withstand the rigors of regular use. Its robust frame and fortified components contribute to its longevity, minimizing the need for frequent repairs or replacements.

Furthermore, the tractor’s maintenance requirements are straightforward. Users will find that routine upkeep is manageable, thanks to accessible engine compartments and clear instructions for oil changes and blade sharpening. This ease of maintenance not only saves time but also contributes to the tractor's overall longevity.

In summary, the Sears 917.257462 is a formidable lawn tractor that combines a powerful engine, versatile cutting capabilities, ergonomic design, and durable construction. Its user-friendly features, coupled with low maintenance requirements, make it an ideal choice for those looking to maintain their lawns with efficiency and ease. Whether grooming a small yard or tackling larger landscapes, this model remains a reliable partner in lawn care.
Top Page Image Contents