Sears 917.257462 manual Assembly, HOW to SET UP Your Tractor

Page 8

i _

ii

I

"_

i I

fill

I Ill"

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

PREPARE BATTERY (See Fig. 3)

CAUTION: Wear eye and face shield.

Wash hands or clothing immediately if accidentally in contact with battery acid.

Do not smoke. Fumes from charged battery acid are explosive.

Read the instructions included with the battery vent caps. Always wear gloves, clothing and goggles to protect your hands, skin and eyes.

Your unit has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•See instructions packed with vent caps in parts bag.

•Fill battery with acid. Fill each cell until it reaches the bottom of the vent wells. Do not overfill.

•Allow battery to stand and settle for at least thirty

minutes. After standing, check the level of acid. If below the vent wells, add more acid until the correct level is reached.

While battery is standing (after adding acid) and later, while battery is being charged, continue with assembly of unit.

IMPORTANT: TO MAXIMIZE THE LIFE OF YOUR BATTERY, IT IS NECESSARY THAT THE BATTERY BE CHARGED

BEFOREUSE. FAILURETO CHARGE BATTERYCANRESULT IN A SHORTENED BATTERY LIFE.

•Charge battery at a rate of 6 amperes for 1 hour. Use a 12 volt battery charger. Observe all safety precau- tions required for battery charging.

INSTALL SEAT (See Fig. 4)

Adjust seat before tightening adjustment bolt.

•Remove cardboard packing on seat pan.

•Place seat on pan and assemble shoulder bolt.

•Assemble adjustment bolt, Iockwasher and flat washer loosely. Do not tighten.

•Tighten shoulder bolt securely.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down (See Fig. 8).

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

 

- FLAT WASHER

ADJUSTMENT

,LOCK WASHER

BOLT

 

•Check the acid level after the battery is charged. Ifthe

acid has fallen below the correct level, add distilled or iron free water.

•Install the vent caps to cover the vent wells. Wash the top of the battery with water to remove any acid, then wipe dry.

•Check battery case for leakage to make sure that no damage has occurred in handling.

•Dispose of excess battery acid. Neutralize acid for disposal by adding it to four inches of water in a five gallon plastic container. Stir with a wooden or plastic paddle while adding baking soda until the addition of more soda causes no more foaming.

•Follow instructions on how to install battery.

CUT AWAY VIEW

VENT CAP

BATTERY

CELL ACID

LEVEL

FIG. 4

CHECKTIRE PRESSURE

The tires on your unit were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" on page 3 of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSIT-ION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

FIG. 3

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see

that the, brake is properly adjusted. See "TO ADJUST BRAKE' in the Service and Adjustments section of this manual.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Sears HP Electric Start 36 Mower Speed Lawn RiderSafety is Involved Safe Operation Practices for Ride-On MowersII. Slope Operation III. ChildrenProduct Specifications Full 90 DAY Warranty on BatteryMaintenance Agreement Customer ResponsibilitiesMaintenance EnginePerformance Sparkplug Muffler AIR Filter Stabilizer Blades BeltsTable of Contents Contents of Hardware Pack Tools Required for Assembly To Remove Unit from CartonBefore Rolling Unit OFF Skid Unpack CartonAssembly HOW to SET UP Your TractorChecklist All assembly instructions have been completedOperation Know Your Lawn RiderTo USE Throttle Control See Fig To Move Forward and BackwardSee Figs To SET Parking Brake See FigTo Adjust Mower Cutting Height Before Starting the EngineTo Operate Mower See Figs To TransportADD Gasoline Important When Operating in TemperaturesMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USELawn Rider Blade CareBlade Removal See Fig Brake OperationTo Clean Battery and Terminals EngineAIR Filter See Fig Transaxle CoolingCleaning AIR Screen See FigMuffler Spark PlugsTo Install Mower See Fig Mower Upstop Adjustment See FigLawn Rider To Remove Mower See FigViewed from Front of Tractor Service and AdjustmentsTo Level Mower Housing See Fig To Adjust Brake See Fig To Adjust Steering Wheel AlignmentKeeper To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Remove Hood See FIGTo Remove Wheel for Repairs See Fig To Replace FuseTo Adjust Carburetor See Fig To Adjust Throttle Control CablePreliminary Setting EngineBattery OtherTractor Fuel SystemTroubleshooting Points Problem Cause CorrectionProblem Cause CorrectionSchematic Wheels Tires DecalsKEY Part Description NO. no USAElectrical Standard Hardware - Purchase Locally ElectricalKEY Part Description Standard Hardware - Purchase Locally HoodUNC 129965 Case, Battery Fender / ChassisFrame 19132012 WasherSeat Locknut, Hex, Larg, FlangeStandard Hardware Purchase Locally 1011Dash Lower, Steering Steering WheelKEY Part NO. no Description Bolt, Hex Sector Gear / Axle SupportLink, Drag Front Axle Cap, Spindle25/32 x 1-5/8 x 16 Gauge Standard Hardware Purchase LocallyBrake / Rear Mower Lift Assembly KEY122504X Hardware Shown LargerEngine / Throttle Standard Hardware PurchaseGround Drive Keeper, Ground Drive Belt, IdlerArm, Ground Drive Clutch Idler, FlatPulley 2530Transaxle Mower Lift Lever Clip, Fuel Line106932X STD560907Mower Deck Mower Deck FOOTE/DANA Transaxle Model Number 2631 2732FOOTE/DANA TRANSAXLE- Model Number Briggs & Stratton Engine Model Number 283707, Type Number 2653O7 219 42242.1 224 138 44566S 310 801490450 399265 Bearing, Cylinder Requires Special 22406193805 391086224546 635 66538Mounting MAX Sighting Guide Only Ride UP and Down HILL, not Across HillSight and Hold this Level with SKY Line or Tree 19.91 HOW to Order Repair PartsModel Number 917,257462

917.257462 specifications

The Sears 917.257462 is a well-known lawn tractor that has earned a reputation for its reliable performance and robust build. Designed for homeowners with medium to large yards, this model combines functionality and ease of use, making it an excellent choice for both novice and experienced gardeners.

One of the standout features of the Sears 917.257462 is its powerful engine. Equipped with a reliable, air-cooled, four-stroke engine, it offers ample horsepower to handle various mowing tasks. The engine's efficient design ensures that it provides consistent power while maintaining fuel economy, allowing owners to tackle extensive lawn areas without frequent refueling.

The cutting system of the Sears 917.257462 is designed for efficiency and versatility. It boasts a durable, reinforced mowing deck that allows for multiple cutting heights, accommodating different grass types and lawn conditions. This adaptability makes it easy to achieve a clean, even cut, regardless of the lawn's terrain. Additionally, the tractor features a bagging system that aids in collecting grass clippings for a tidy finish.

Ergonomics play a crucial role in the design of the Sears 917.257462. The operator's seat is adjustable, providing comfort and promoting good posture during extended use. The steering system is responsive, facilitating easy maneuverability around obstacles in the yard. The controls are intuitively placed, making it simple for users to operate the tractor while focusing on the task at hand.

Another key characteristic of this tractor is its durability. Constructed with high-quality materials, the Sears 917.257462 is built to withstand the rigors of regular use. Its robust frame and fortified components contribute to its longevity, minimizing the need for frequent repairs or replacements.

Furthermore, the tractor’s maintenance requirements are straightforward. Users will find that routine upkeep is manageable, thanks to accessible engine compartments and clear instructions for oil changes and blade sharpening. This ease of maintenance not only saves time but also contributes to the tractor's overall longevity.

In summary, the Sears 917.257462 is a formidable lawn tractor that combines a powerful engine, versatile cutting capabilities, ergonomic design, and durable construction. Its user-friendly features, coupled with low maintenance requirements, make it an ideal choice for those looking to maintain their lawns with efficiency and ease. Whether grooming a small yard or tackling larger landscapes, this model remains a reliable partner in lawn care.
Top Page Image Contents