Sears 917.257462 manual Engine, To Adjust Carburetor See Fig, To Adjust Throttle Control Cable

Page 22

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

(See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from "SLOW" to "CHOKE" position. Slowly move lever from "CHOKE" to "FAST" position.

•Check that holes "A" in governor control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clam€ screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNORGOVERNOR

CONTROL LEVER

CONTROL PLATE

HOLES "A"

CLAMP

THRO'I'rLE

 

SCREW

CABLE

FIG. 32

TO ADJUST CARBURETOR (See Fig. 33)

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjust- ment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turnig idle mixture valve in (clockwise) de- creases the supply offuel to the engine giving a leaner fuel/ air mixture. Turning the idle mixture valve out (counter- clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: DAMAGE TO THE NEEDLE VALVE AND

THE SEAT IN CARBURETOR MAY RESULT IF SCREW IS

TURNED IN TOO TIGHT.

PRELIMINARY SETTING -

Air cleaner assembly must be assembled to the carbu- retor when making carburetor adjustments.

Be sure the throttle control cable is adjusted properly (see above).

With engine off turn idle mixture valve in (clockwise) closing it finger tight and then turn out (counterclock-

wise) 1 fullturn.

FINAL SE]-FING -

•Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in "NEUTRAL" position.

•Move throttle control lever to "SLOW" position. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

•While still holding throttle lever against idle speed screw, turn idle mixture valve in (clockwise) until en- gine begins to die and then turn out (counterclockwise) until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST-

•Move throttle control lever from "SLOW" to "FAST" position. If engine hesitates or dies, turn idle mixture

valve out (counterclockwise) 1/8 turn. Rep.eat test and continue to adjust, if necessary, until engine acceler- ates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT; NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IFYOU THINKTHE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEARESTAUTHORIZED SERVICE CENTER, WHICH HAS PROPER EQUIPMENTAND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

THROTTLEIDLE SPEED

LEVER _

SCREW

FIG. 33

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Sears HP Electric Start 36 Mower Speed Lawn RiderII. Slope Operation Safety is InvolvedSafe Operation Practices for Ride-On Mowers III. ChildrenMaintenance Agreement Product SpecificationsFull 90 DAY Warranty on Battery Customer ResponsibilitiesPerformance MaintenanceEngine Sparkplug Muffler AIR Filter Stabilizer Blades BeltsTable of Contents Contents of Hardware Pack Before Rolling Unit OFF Skid Tools Required for AssemblyTo Remove Unit from Carton Unpack CartonAssembly HOW to SET UP Your TractorChecklist All assembly instructions have been completedOperation Know Your Lawn RiderSee Figs To USE Throttle Control See FigTo Move Forward and Backward To SET Parking Brake See FigTo Operate Mower See Figs To Adjust Mower Cutting HeightBefore Starting the Engine To TransportMowing Tips Important When Operating in TemperaturesADD Gasoline General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig Lawn RiderBlade Care Brake OperationAIR Filter See Fig To Clean Battery and TerminalsEngine Transaxle CoolingMuffler CleaningAIR Screen See Fig Spark PlugsLawn Rider To Install Mower See FigMower Upstop Adjustment See Fig To Remove Mower See FigTo Level Mower Housing See Fig Service and AdjustmentsViewed from Front of Tractor Keeper To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigTo Remove Hood See FIG To Replace FusePreliminary Setting To Adjust Carburetor See FigTo Adjust Throttle Control Cable EngineTractor BatteryOther Fuel SystemTroubleshooting Points Problem Cause CorrectionProblem Cause CorrectionSchematic KEY Part Description NO. no Wheels TiresDecals USAElectrical KEY Part Description ElectricalStandard Hardware - Purchase Locally UNC HoodStandard Hardware - Purchase Locally Frame 129965 Case, BatteryFender / Chassis 19132012 WasherSeat Locknut, Hex, Larg, FlangeDash 1011Standard Hardware Purchase Locally KEY Part NO. no Description Steering WheelLower, Steering Link, Drag Sector Gear / Axle SupportBolt, Hex 25/32 x 1-5/8 x 16 Gauge Front AxleCap, Spindle Standard Hardware Purchase Locally122504X Brake / Rear Mower Lift AssemblyKEY Hardware Shown LargerEngine / Throttle Standard Hardware PurchaseArm, Ground Drive Clutch Ground DriveKeeper, Ground Drive Belt, Idler Idler, FlatTransaxle 2530Pulley 106932X Mower Lift LeverClip, Fuel Line STD560907Mower Deck Mower Deck FOOTE/DANA Transaxle Model Number 2631 2732FOOTE/DANA TRANSAXLE- Model Number 3O7 Briggs & Stratton Engine Model Number 283707, Type Number265 219 42266S 224 138 44542.1 310 80193805 490450399265 Bearing, Cylinder Requires Special 224061 391086Mounting 635 66538224546 Sight and Hold this Level with SKY Line or Tree Sighting Guide Only Ride UP and Down HILL, not Across HillMAX Model Number 917,257462 HOW to Order Repair Parts19.91

917.257462 specifications

The Sears 917.257462 is a well-known lawn tractor that has earned a reputation for its reliable performance and robust build. Designed for homeowners with medium to large yards, this model combines functionality and ease of use, making it an excellent choice for both novice and experienced gardeners.

One of the standout features of the Sears 917.257462 is its powerful engine. Equipped with a reliable, air-cooled, four-stroke engine, it offers ample horsepower to handle various mowing tasks. The engine's efficient design ensures that it provides consistent power while maintaining fuel economy, allowing owners to tackle extensive lawn areas without frequent refueling.

The cutting system of the Sears 917.257462 is designed for efficiency and versatility. It boasts a durable, reinforced mowing deck that allows for multiple cutting heights, accommodating different grass types and lawn conditions. This adaptability makes it easy to achieve a clean, even cut, regardless of the lawn's terrain. Additionally, the tractor features a bagging system that aids in collecting grass clippings for a tidy finish.

Ergonomics play a crucial role in the design of the Sears 917.257462. The operator's seat is adjustable, providing comfort and promoting good posture during extended use. The steering system is responsive, facilitating easy maneuverability around obstacles in the yard. The controls are intuitively placed, making it simple for users to operate the tractor while focusing on the task at hand.

Another key characteristic of this tractor is its durability. Constructed with high-quality materials, the Sears 917.257462 is built to withstand the rigors of regular use. Its robust frame and fortified components contribute to its longevity, minimizing the need for frequent repairs or replacements.

Furthermore, the tractor’s maintenance requirements are straightforward. Users will find that routine upkeep is manageable, thanks to accessible engine compartments and clear instructions for oil changes and blade sharpening. This ease of maintenance not only saves time but also contributes to the tractor's overall longevity.

In summary, the Sears 917.257462 is a formidable lawn tractor that combines a powerful engine, versatile cutting capabilities, ergonomic design, and durable construction. Its user-friendly features, coupled with low maintenance requirements, make it an ideal choice for those looking to maintain their lawns with efficiency and ease. Whether grooming a small yard or tackling larger landscapes, this model remains a reliable partner in lawn care.
Top Page Image Contents