Sears 917.257462 manual Tools Required for Assembly, To Remove Unit from Carton, Unpack Carton

Page 7

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

STEERING SHAFT

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

9/16" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

(1)

1/2" wrench

Screwdriver

(1)

3/4" wrench

Utility knife

When right and left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE UNIT FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton (See page 6).

•Cut along dotted lines on the carton, from top to bottom, all four corners of carton and lay panels fiat.

•Check for any additional loose parts or cartons and remove.

ATTACH STEERING WHEEL

POSITION STEERING SHAFT (See Fig. 1) -

•Lift hood.

•Pull steering shaft up to engage gears.

•Push steering clip through hole on steering shaft at 45° (hole is located under dash and above lower steering bushing).

•Push steering clip onto steering shaft until steering clip snaps into place.

INSTALL STEERING WHEEL (See Fig. 2) -

•Slide the steering sleeve over the steering shaft (Bot- tom of sleeve goes over ring on dash).

•Slidesteering wheel adapter onto uppersteering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

•Position steering wheel so cross bars are horizontal (left to right) andslide onto adapter.

•Assemble large flat washer and 3/8-24 Iocknut and tighten securely.

•Snap insert into center of steering wheel.

•Remove protective plastic from tractor hood and grill.

BEFORE ROLLING UNIT OFF SKID

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN

SKID THAT MAY PUNCTURE TIRES WHERE UNIT IS TO ROLL

OFF SKID.

•Raise mower lift lever to its highest position.

•Place gearshift lever in "NEUTRAL" position.

•Release parking brake by depressing clutch/brake pedal.

•Roll unit backwards off skid.

•Remove banding holding discharge guard up against tractor.

;TEERING SHAFT

STEERING CLIP

LOWER

BUSHING

FIG. 1

STEERING WHEEL

INSERT

LOCKNUT

WASHER

_STEERINGWHEEL

STEERING WHEEL

STEERING SLEEVE

STEERING SHAFT

FIG. 2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents HP Electric Start 36 Mower Speed Lawn Rider SearsIII. Children Safety is InvolvedSafe Operation Practices for Ride-On Mowers II. Slope OperationCustomer Responsibilities Product SpecificationsFull 90 DAY Warranty on Battery Maintenance AgreementSparkplug Muffler AIR Filter Stabilizer Blades Belts MaintenanceEngine PerformanceTable of Contents Contents of Hardware Pack Unpack Carton Tools Required for AssemblyTo Remove Unit from Carton Before Rolling Unit OFF SkidHOW to SET UP Your Tractor AssemblyAll assembly instructions have been completed ChecklistKnow Your Lawn Rider OperationTo SET Parking Brake See Fig To USE Throttle Control See FigTo Move Forward and Backward See FigsTo Transport To Adjust Mower Cutting HeightBefore Starting the Engine To Operate Mower See FigsMowing Tips Important When Operating in TemperaturesADD Gasoline Before Each USE MaintenanceLubrication Chart General RecommendationsBrake Operation Lawn RiderBlade Care Blade Removal See FigTransaxle Cooling To Clean Battery and TerminalsEngine AIR Filter See FigSpark Plugs CleaningAIR Screen See Fig MufflerTo Remove Mower See Fig To Install Mower See FigMower Upstop Adjustment See Fig Lawn RiderTo Level Mower Housing See Fig Service and AdjustmentsViewed from Front of Tractor To Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment KeeperTo Replace Fuse To Start Engine with a Weak Battery See FigTo Remove Hood See FIG To Remove Wheel for Repairs See FigEngine To Adjust Carburetor See FigTo Adjust Throttle Control Cable Preliminary SettingFuel System BatteryOther TractorProblem Cause Correction Troubleshooting PointsCause Correction ProblemSchematic USA Wheels TiresDecals KEY Part Description NO. noElectrical KEY Part Description ElectricalStandard Hardware - Purchase Locally UNC HoodStandard Hardware - Purchase Locally 19132012 Washer 129965 Case, BatteryFender / Chassis FrameLocknut, Hex, Larg, Flange SeatDash 1011Standard Hardware Purchase Locally KEY Part NO. no Description Steering WheelLower, Steering Link, Drag Sector Gear / Axle SupportBolt, Hex Standard Hardware Purchase Locally Front AxleCap, Spindle 25/32 x 1-5/8 x 16 GaugeHardware Shown Larger Brake / Rear Mower Lift AssemblyKEY 122504XStandard Hardware Purchase Engine / ThrottleIdler, Flat Ground DriveKeeper, Ground Drive Belt, Idler Arm, Ground Drive ClutchTransaxle 2530Pulley STD560907 Mower Lift LeverClip, Fuel Line 106932XMower Deck Mower Deck 2631 2732 FOOTE/DANA Transaxle Model NumberFOOTE/DANA TRANSAXLE- Model Number 219 422 Briggs & Stratton Engine Model Number 283707, Type Number265 3O766S 224 138 44542.1 801 310391086 490450399265 Bearing, Cylinder Requires Special 224061 93805Mounting 635 66538224546 Sight and Hold this Level with SKY Line or Tree Sighting Guide Only Ride UP and Down HILL, not Across HillMAX Model Number 917,257462 HOW to Order Repair Parts19.91

917.257462 specifications

The Sears 917.257462 is a well-known lawn tractor that has earned a reputation for its reliable performance and robust build. Designed for homeowners with medium to large yards, this model combines functionality and ease of use, making it an excellent choice for both novice and experienced gardeners.

One of the standout features of the Sears 917.257462 is its powerful engine. Equipped with a reliable, air-cooled, four-stroke engine, it offers ample horsepower to handle various mowing tasks. The engine's efficient design ensures that it provides consistent power while maintaining fuel economy, allowing owners to tackle extensive lawn areas without frequent refueling.

The cutting system of the Sears 917.257462 is designed for efficiency and versatility. It boasts a durable, reinforced mowing deck that allows for multiple cutting heights, accommodating different grass types and lawn conditions. This adaptability makes it easy to achieve a clean, even cut, regardless of the lawn's terrain. Additionally, the tractor features a bagging system that aids in collecting grass clippings for a tidy finish.

Ergonomics play a crucial role in the design of the Sears 917.257462. The operator's seat is adjustable, providing comfort and promoting good posture during extended use. The steering system is responsive, facilitating easy maneuverability around obstacles in the yard. The controls are intuitively placed, making it simple for users to operate the tractor while focusing on the task at hand.

Another key characteristic of this tractor is its durability. Constructed with high-quality materials, the Sears 917.257462 is built to withstand the rigors of regular use. Its robust frame and fortified components contribute to its longevity, minimizing the need for frequent repairs or replacements.

Furthermore, the tractor’s maintenance requirements are straightforward. Users will find that routine upkeep is manageable, thanks to accessible engine compartments and clear instructions for oil changes and blade sharpening. This ease of maintenance not only saves time but also contributes to the tractor's overall longevity.

In summary, the Sears 917.257462 is a formidable lawn tractor that combines a powerful engine, versatile cutting capabilities, ergonomic design, and durable construction. Its user-friendly features, coupled with low maintenance requirements, make it an ideal choice for those looking to maintain their lawns with efficiency and ease. Whether grooming a small yard or tackling larger landscapes, this model remains a reliable partner in lawn care.
Top Page Image Contents