Tiger RBF-19C manual Fitting Controls, Lever Unit

Page 40

ASSEMBLY

FITTING CONTROLS

The position of the lever unit inside the tractor cab depends largely upon the route of the cables between unit and control valve.

The control valve is mounted on the front face of the oil tank.

The cable normally can be routed through the rear cab window and should be as free of bends as possible. DO NOT PINCH CABLE IN CLOSED WINDOW.

NOTE: Avoid sharp bends. The rotor control cable must not have a bend of less than 150mm (6 in) radius.

If the tractor cab has special apertures for cables the lever unit should be through them before they are attached to the tractor cab.

Follow instructions below for fitting lever unit.

A. Pass lever unit and cable through suitable aperture in rear of tractor cab.

NOTE: It is essential not to drill mounting holes through any structural member of the safety cab.

B.Mount the unit securely on to the mounting bracket with bolts provided.

C.Finally, check levers for smooth operation in both directions. If any stiffness is felt or if levers do not return to center, check cable route for sharp bends.

NOTE: Whenever the machine is removed and the tractor is operated without the control valve unit in place, fit rubber beading (contained in the cab fitting kit) to the edge of the console mounting bracket to prevent risk of injury.

LEVER UNIT

A.Adjustment is provided at the cable attachment to the control valve.

B.Loosen locknut on the cable/valve connection flange FIGURE 3-5 (A).

C.Loosen the two capscrews holding the valve connection flange FIGURE 3-5 (B).

FIGURE 3-5

RBF-19C 07-04

Assembly Section 3-6

© 2004 Alamo Group Inc.

 

Page 39 Page 41
Image 40
Page 39 Page 41
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Tractor Requirements GeneralMachine Preparation Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitHydraulic Systems Adjust Lever Pivot PositionFill Tank with OIL RBF-19C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 19C Assembly Section Bleeding Rams Initial RUNBleeding the First Ram Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements Operator RequirementsTractor Requirements and Capabilities Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceFrame Assembly Boom Unit Pre-Operation Inspection and ServiceBoom ARM Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsRoller Height Grass FlailGround Level and Scrub Cutting lower roller to its maximum Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents