Tiger RBF-19C Boom Unit Pre-Operation Inspection and Service, Frame Assembly, Boom ARM Assembly

Page 61

OPERATION

6.2 Boom Unit Pre-Operation Inspection and Service

Inspect and service the boom arm and head prior to operation. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the unit is ready for operation, conduct the following:

¾Ensure that the Manual Canister is secured to the Boom unit with the Operator’s Manual inside.

¾Ensure all decals are in place and legible. Replace missing, worn, and non-legible decals.

NOTE: The mower Operator’s Manual and affixed Decals contain important instructions on the safe and proper use of the mower. Maintain these important safety features on the mower in good condition to ensure the information is available to the operator at all times.

FRAME ASSEMBLY

¾Inspect condition of mounting frame weldment.

¾Inspect condition of King Post frame.

¾Ensure all bolts and screws are in position and are properly torqued.

¾Ensure all pins are in place and fastened with screws.

¾Ensure frame is properly mounted to tractor and hardware is properly installed and tightened.

BOOM ARM ASSEMBLY

¾Inspect condition of each arm section weldment

¾Ensure all pins are in place.

¾Ensure all bolts and screws are properly installed.

¾Check condition of teflon bushings at boom pivot points.

¾Ensure each hydraulic cylinder is installed and retained correctly. Ensure the proper size pins are used to retain the cylinders in place and are secured properly.

¾Ensure that all joints are lubricated. See Maintenance Section for Lubrication Chart.

Frame

Weldment

WARNING!

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion

 

or while tractor engine is running. Make sure the tractor engine is off before working on the

 

Implement. (SG-20)

 

RBF-19C 07/04

Operation Section 4-11

© 2004 Alamo Group Inc.

 

Page 60 Page 62
Image 61
Page 60 Page 62
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Duties This Act SeeksOsha Regulations Employer ResponsibilitiesIntroduction Section Before Operating this Machine IntroductionAssembly Section Tractor Requirements GeneralMachine Preparation Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsHydraulic Systems Adjust Lever Pivot PositionFill Tank with OIL RBF-19C Assembly Section Fitting Rotor Unit Mechanical Breakout Connecting the MotorHose Layout TwistsChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 19C Assembly Section Bleeding Rams Initial RUNBleeding the First Ram Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Tractor Requirements Operator RequirementsTractor Requirements and Capabilities Rops and Seat Belt Shatter Proof Safety WindowsOperator Thrown Object Protection Tractor Lighting and SMV EmblemTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceFrame Assembly Boom Unit Pre-Operation Inspection and ServiceBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedRoller Height Grass FlailGround Level and Scrub Cutting lower roller to its maximum Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Gearbox LubricationGrease Points PTO Drive TubesPower TAKE-OFF Shaft Filter ReplacementHoses and Rotor Drive Circuit Hydraulic OilsHydraulic Cylinders Rotor UnitStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents