Tiger RBF-19C manual TRACTOR, BOOM, and Attached Head Storage, Shutting Down the Attached Head

Page 77
(SG-9)

OPERATION

9.4 Shutting Down the Attached Head

To shut down attached boom head, first bring the tractor to a complete stop. Keep the engine speed at normal operating speed of 540 RPM, and push the Motor Switch IN to the Stop position. The mower head will come to a complete stop with in 15 seconds.

ON-OFF Switch

Park the tractor on a level surface, place the transmission in park or neutral and apply the parking brake, shut down the engine, remove the key, and wait for all motion to come to a complete stop before exiting the tractor.

DANGER! BEFORE leaving the tractor seat, always engage the brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only.

10. TRACTOR, BOOM, AND ATTACHED HEAD STORAGE

Properly preparing and storing the unit at the end of the season is critical to maintaining its appearance and to help ensure years of dependable service. The following are suggested storage procedures:

1.Thoroughly clean all debris from boom and head to prevent damage from rotting grass and standing water.

2.Lubricate all grease points and fill oil levels according to the maintenance lubrication schedule.

3.Tighten all bolts to the proper torque. Ensure all pins and other hardware are in place.

4.Check the boom arm and head for worn and damaged parts. Perform repairs and make replacements so that the mower will be ready for use at the start of the next season.

5.Install leg supports to reduce tension on boom and tank during storage.

6.Store the unit in a clean and dry location.

7.Use spray touch-up enamel where necessary on bare metal surfaces to prevent rust and to maintain the appearance of the mower.

RBF-19C 07/04

Operation Section 4-27

© 2004 Alamo Group Inc.

 

Image 77
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Duties This Act SeeksOsha Regulations Employer ResponsibilitiesIntroduction Section Before Operating this Machine IntroductionAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-19C Assembly Section Fitting Rotor Unit Mechanical Breakout Connecting the MotorHose Layout TwistsChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 19C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Rops and Seat Belt Shatter Proof Safety WindowsOperator Thrown Object Protection Tractor Lighting and SMV EmblemTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Gearbox LubricationGrease Points PTO Drive TubesPower TAKE-OFF Shaft Filter ReplacementHoses and Rotor Drive Circuit Hydraulic OilsHydraulic Cylinders Rotor UnitStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.