Tiger RBF-19C manual Close Isolator Valves on First ARM and Accumulator if Fitted

Page 87

MAINTENANCE

B.Remove stands from underneath the tank and fit to the mainframe.

C.Lengthen to link so that the weight of the machine is on the rear stand.

D.Remove pin connecting the right frame to the tractor, and lower the three point linkage so that the weight of the machine is on the front stands.

E.Stop Tractor engine.

F.Open accumulator valve and operate control levers in both directions to release pressure.

G.CLOSE ISOLATOR VALVES ON FIRST ARM AND ACCUMULATOR (IF FITTED).

H.Remove control lever unit from inside tractor and feed through rear of cab without bending cable too tightly. Tie unit onto mainframe and protect from weather.

I.Disconnect cable from control box to control valve and feed through rear of cab.

J.Release tractor end of PTO shaft and pull back along splined (on some tractors it may not be possible to remove the PTO completely at this stage).

K.Remove lower link pins.

L.Start tractor engine and drive carefully forward, releasing machine and PTO shaft from tractor.

M.Replace lower link pins and place cap over tractor PTO.

N.Remove control box from cab and store in a clean dry place.

FIGURE 5-2

RBF-19C 07/04

Maintenance Section 5-5

© 2004 Alamo Group Inc.

 

Page 86 Page 88
Image 87
Page 86 Page 88
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Stop Mowing if Passersby are Within 100 Yards UN- Less Equipment Operation Safety Instructions and PracticesSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 See Your Tiger Dealer Parts InformationTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Employer Responsibilities This Act SeeksDuties Osha RegulationsIntroduction Section Before Operating this Machine IntroductionAssembly Section General Tractor RequirementsMachine Preparation Fitting Machine to Tractor Assembly Section Fitting PTOLever Unit Fitting ControlsAdjust Lever Pivot Position Hydraulic SystemsFill Tank with OIL RBF-19C Assembly Section Fitting Rotor Unit Twists Connecting the MotorMechanical Breakout Hose LayoutChafing Hoses Sharp BendsAccumulator KIT Flexible Front Guard KITRBF 19C Assembly Section Initial RUN Bleeding RamsBleeding the First Ram Assembly Page Operation Section Operation Tiger Rear Mount Boom Operation Instructions Connectingattaching HeadsOperation Operator Requirements Tractor RequirementsTractor Requirements and Capabilities Tractor Lighting and SMV Emblem Shatter Proof Safety WindowsRops and Seat Belt Operator Thrown Object ProtectionTractor Ballast Getting on and OFF the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Dash Nominal Torque Value Size IN.LBS FT.LBS Connecting Attaching Head to the BoomTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service Frame AssemblyBoom ARM Assembly Hydraulic PUMP/OIL Reservoir Hydraulic Line InspectionFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating the Attached Mower Heads Operating Speed and Ground SpeedGrass Flail Roller HeightGround Level and Scrub Cutting lower roller to its maximum Operation Grass Cutting Alternative Rotor Link PositionsStalling the Rotor Hedge TrimmingMotor Position Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head StorageTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section PTO Drive Tubes LubricationGearbox Grease PointsHydraulic Oils Filter ReplacementPower TAKE-OFF Shaft Hoses and Rotor Drive CircuitParking and Removal Rotor UnitHydraulic Cylinders StorageClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents