Tiger RBF-19C manual Getting on and OFF the Tractor, Tractor Ballast

Page 56
(SBM-11)

OPERATION

2.4 Tractor Ballast

To ensure tractor stability when operating on flat surfaces the left rear tractor tire MUST exert a minimum down force (weight) of 1500 lbs. on the ground when the tractor is on level ground, its boom is fully extended and the mower head is horizontal and two feet above the ground. For units which have the ability to operate on either side of the tractor, these requirements must also be met for the right side tire when the boom is extended to the left side as described above. A tractor that does not meet this criteria is DANGEROUS and should not be operated as upset of the unit can occur resulting in possible serious injury and property damage. NOTE: All factory mounted units are tested and meet the ballast requirement before shipment; further testing is not required unless the unit is operated in a manner other than what is considered standard operating conditions.

For additional information on properly ballasting the tractor, refer to Alamo Industrial Tractor and Mower Stability Pamphlet P/N #02959010.

DANGER! Each Rear Wheel must have a minimum of 1500 pound contact with the surface to prevent lateral instability and possible tip-over which could result in serious bodily injury or even death. Widen the wheel tread and add weights if needed. Refer to the mounting instructions or call Customer Service if you need assistance with Counterweight Procedure.

If the unit is operated on slopes greater than 5°, additional counterweight will be required. Operation of the unit on slopes greater than 11° is not recommended under any circumstances. On a tractor with a 96” outside to outside tire spread, a 11° slope occurs when one rear tractor tire is about 8” lower than the other rear tire.

WARNING! Do not operate the unit under any circumstance if the slope is 10° or greater.

3. GETTING ON AND OFF THE TRACTOR

The operator must read and completely understand this manual and the tractor operator’s manual before starting any boom mower operation. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. If the operator of the equipment can not read the manuals for themselves, it is the supervisors responsibility to read and explain the manuals and operating instructions to them.

RBF-19C 07/04

Operation Section 4-6

© 2004 Alamo Group Inc.

 

Page 55 Page 57
Image 56
Page 55 Page 57
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety This Act Seeks DutiesOsha Regulations Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-19C Assembly Section Fitting Rotor Unit Connecting the Motor Mechanical BreakoutHose Layout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 19C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Shatter Proof Safety Windows Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Lubrication GearboxGrease Points PTO Drive TubesFilter Replacement Power TAKE-OFF ShaftHoses and Rotor Drive Circuit Hydraulic OilsRotor Unit Hydraulic CylindersStorage Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents