Tiger RBF-19C manual Alternative Rotor Link Positions, Grass Cutting

Page 74

OPERATION

ALTERNATIVE ROTOR LINK POSITIONS

To enable extra angling (on the 1948) of the rotor unit three positions for the attachment of rotor link to cylinder link are provided. To achieve more downward angle of the rotor unit (for trimming far sides of hedges, down steep banks, etc.) the pivot pin should be fitted through the hole FIGURE 4-2 (A) and for close in work (with rotor unit angled vertically upwards) through the hole FIGURE 4-2 (B) in the ram link. The hole FIGURE 4-2

(D)is an intermediate hole. A. Rest rotor unit on ground.

B. Remove linch pin and link pin.

C.Retract or extend third ram depending on which hole is being used.

D.Replace Pin.

Grass Cutting

A.Run the rotor at normal speed (I.E. 540 rev/min. PTO speed)

B.Avoid taking in too much grass by regulating tractor speed.

C.If rotor shaft slows down or chokes up in grass, raise the rotor unit and allow grass to fall clear.

D.Before proceeding with the cutting let rotor speed pick up again.

E.Advantage may be gained in exceptional conditions by taking a narrow cut with part of the rotor shaft running idle.

F.When working alongside or clearing ditches, take a cut along the edge of the ditch so that the ditch limits can be seen.

G.Keep the highest point of the mower arms directly over the obstacle when working over a hedge or into a ditch.

RBF-19C 07/04

Operation Section 4-24

© 2004 Alamo Group Inc.

 

Page 73 Page 75
Image 74
Page 73 Page 75
Contents RBF-19C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoAgent. SG-22 Wait a minute...Save a life Not match the Tractor PTO Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards UN- LessSBM-10 Stop Mowing if Passersby are Within 100 Yards Unless Dismounting.SG-39 SGM-7 SGM-11 Maintenance and Service Safety Instructions and Practices Or death. SBM-12 Parts Information See Your Tiger DealerTransporting Safety Instructions and Practices Regulations. SG-6 Storage and Parking Safety Instructions and Practices 14 11 10 25 20 QTY Level Description Safety Safety Safety Safety Safety Safety Safety Safety Osha Regulations This Act SeeksDuties Employer ResponsibilitiesIntroduction Section Introduction Before Operating this MachineAssembly Section Machine Preparation GeneralTractor Requirements Fitting Machine to Tractor Assembly Fitting PTO SectionFitting Controls Lever UnitFill Tank with OIL Adjust Lever Pivot PositionHydraulic Systems RBF-19C Assembly Section Fitting Rotor Unit Hose Layout Connecting the MotorMechanical Breakout TwistsSharp Bends Chafing HosesFlexible Front Guard KIT Accumulator KITRBF 19C Assembly Section Bleeding the First Ram Initial RUNBleeding Rams Assembly Page Operation Section Connectingattaching Heads Operation Tiger Rear Mount Boom Operation InstructionsOperation Tractor Requirements and Capabilities Operator RequirementsTractor Requirements Operator Thrown Object Protection Shatter Proof Safety WindowsRops and Seat Belt Tractor Lighting and SMV EmblemGetting on and OFF the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Dash Nominal Torque Value Size IN.LBS FT.LBSPRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom ARM Assembly Boom Unit Pre-Operation Inspection and ServiceFrame Assembly Hydraulic Line Inspection Hydraulic PUMP/OIL ReservoirFlail Head Inspection Operating the Control Valves Valve Operation Plate P/N Driving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Mower Operating the Boom Unit and Attached Head Foreign Debris Hazards / Overhead Obstructions Operating Speed and Ground Speed Operating the Attached Mower HeadsGround Level and Scrub Cutting lower roller to its maximum Grass FlailRoller Height Operation Alternative Rotor Link Positions Grass CuttingHedge Trimming Stalling the RotorMotor Position TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Mower Transporting on Public Roadways Hauling the Tractor and Mower Trouble Shooting Guide Page Maintenance Section Grease Points LubricationGearbox PTO Drive TubesHoses and Rotor Drive Circuit Filter ReplacementPower TAKE-OFF Shaft Hydraulic OilsStorage Rotor UnitHydraulic Cylinders Parking and RemovalClose Isolator Valves on First ARM and Accumulator if Fitted Proper Torque for Fasteners Figure Warranty Information ONE Last Word RBF-19C-OMWPL-07/04 Printed U.S.A

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents